Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. mildmanrd

    Connecting laptop to PC direct cable conn

    Have you selected the folders or drive that you want to share by right-clicking on that item and enabling the sharing features?
  2. mildmanrd

    PPP configurations

    trevorh13, let's assume that hostname router1 is your local router and hostname router2 is your remote router. On your remote router, you need to add the username router1 and the password it should expect. ex. router2(config)#username router1 password whatever then on router1 you need to make...
  3. mildmanrd

    Carrier Transitions/Loss of Frame Between Cisco 1720 Routers !

    Hi evilh, I would try placing a loopback plug in the wic card and issue the debug serial interface command. If the keepalives are incrementing then your card is fine, if they don't then it may be faulty. Also on your remote router I would verify that you are using the ip helper-address...
  4. mildmanrd

    How difficult is it to connect to web

    Here it is quick and dirty: websites are hosted on computers computers are grouped in networks networks are connected by routers routers are owned by ISPs users dial-in to ISPs for access
  5. mildmanrd

    How to tell the difference between 4500 and 4500M?

    Try the command "show hardware"
  6. mildmanrd

    HTTP vulnerability

    Hi, I've just read the vulnerability and tried it on my 2501 running IOS 11.3(11a) with success. Just follow the steps as described and it will work. open up a browser and type: http://address/level/xx/exec/ ex. http://10.2.1.1/level/16/exec/ http://10.2.1.1/level/17/exec/...
  7. mildmanrd

    How to Add/Delete Users for Telnet Access- Cisco 2600

    Also keep in mind the router may be pointing to a tacacs or radius server for authentication so you may need add and remove users there.
  8. mildmanrd

    How to Add/Delete Users for Telnet Access- Cisco 2600

    This sounds like a job for AAA. To add users to the router's local database you would issue a command like this in global config mode: ex. router(config)#username WurlyBurly password iwantin router(config)#username admin password letmein To remove users from the local database just issue the...
  9. mildmanrd

    Needs help..

    Try plugging in a loopback as wybnormal suggested and do a debug serial interface and check to see if your keepalives are incrementing. If they are not, then you may have a defective port.
  10. mildmanrd

    router 1601 crash and shutdown

    I noticed a typo in your config that may have something to do with it. Your ip pool name is "dial" however on your serial interface you named it "dia", this will cause an ip conflict when your pc requests an address.
  11. mildmanrd

    Frame Relay - Green, Amber and Red frames.. Please help

    I'm not sure either but I will take a stab at it. The equation for frame is: CIR=Bc/Tc where Tc is the time in seconds defined by your provider. So, applying this formula will yield CIR=64kbits/2secs CIR=32kbits/sec The provider is saying they will allow you 64kbits of thruput in 2 seconds...
  12. mildmanrd

    Frame-Relay Configuration

    I'm not quite sure what the problem is however I think it may be with the default routes like jeter suggested. I noticed that you are using DDR on the BRI which is triggered with any IP traffic. So maybe when you try to ping, it brings up the DDR link, so traffic is trying to exit out of BRI...
  13. mildmanrd

    debug messages

    terminal monitor
  14. mildmanrd

    split horizon

    By definition, split horizon will block routing updates from being sent out of the same interface it learned the update to begin with. In frame relay,you can have multiple networks connected to the same 'physical' interface. Without using subinterfaces(logical interfaces of the physical) in...
  15. mildmanrd

    Newbie ques: Routing external ip's with 1601

    You can use static NAT mappings to do the job. This will help provide a little security as opposed to using the 'real addresses'. To configure follow these steps (assuming you are a little familiar with cisco IOS): -console into router -get into interface config mode for ethernet 0 -apply...
  16. mildmanrd

    Networking 2 PCs at home

    Can you ping the other pc? Do you have both machines in the same workgroup?
  17. mildmanrd

    CD Rom Installation Problem with Mandrake

    Hi, I'm a linux newbie as well and had a similar problem when installing Slackware 7.1. After a week of pulling my hair out, I decided to format and fdisk my hard drive. I created an active DOS partition of 800 megs, installed a DOS driver for my cdrom drive, and xcopied the entire contents of...
  18. mildmanrd

    Cannot ping SCO server from win98 box

    If all of the win98 boxes are on the same subnet then I'm not sure, however if they are not then the first thing that comes to mind is the default gateway address.

Part and Inventory Search

Back
Top