Search results for query: *

Excellent. Worked perfectly. Thank you very much.

I do a search within "Phones" and the device profile is not showing for them. Most of these users do not have a physical phone associated with them considering they move around a lot and use extension mobility. Thank you.

Cisco CUCM Hello, We have numerous people here that will use the same phone device depending on their work schedule. Most DN's are only associated with a Device Profile. Is there a way to tell the MAC address of the phone set that someone has logged into using their Device Profile...

Hello, Does anyone know how I can obtain the voice DNIS translations within a Cisco Router? Example is below. alias 1 2482227404 to 7404 I would appreciate any assistance anyone can provide. Thank you, Olympus41

Hello, We have a Nortel Option 81 CS1000 PBX with a PRI trunk group that is connected to our Asterisk Free PBX system. We have it setup on the Free PBX to send all calls that are dialed as "9+1+NPA+1234567" to our Nortel PBX over the Virtual PRI trunk group sending "9+1+NPA+1234567"...

Allenmac, Thank you for the suggestion, but it did not make a difference :(

We have a SIP trunk group that we are using for office-to-office calling and also VOIP to the carrier. The route is setup on the PBX for outbound calls to do LINEAR and all inbound to the PBX is setup to arrive on the first channel, second channel, etc. We keep receiving the message “PRI101 255...

Hello, We are using VOIP for our inbound and outbound calls. The issue we are experiencing is that if a call is received inbound from outside and then forwarded by our system to an outside number via VOIP, the “History” information being passed to the carrier exceeds 2,000 characters...

Worked perfectly. Thank you very much for your quick response.

StanleySteamer, I have looked and do not see where the change would be made within LD95. Please advise. TYPE CPND CUST 0 CNFG ALON MXLN 27 STAL YES DFLN 13 DES NO RESN YES CFWD F CFNA N HUNT B PKUP P XFER T AAA A ECSL

We have recently rolled out the ability for our employees to dial external phone numbers via SIP through our carrier. The problem we are experiencing is that the CPND of the phone set that is making the call to an external phone number via SIP is passing with their calling phone number. We...

So if I set both clock controllers to FREE RUN, that will allow the PBX to clock internally, correct? Thank you, Olympus41

Anyone have any other ideas?

TYPE RDR_DATA CUST 00 OPT CFF CFRD PVCD CWRD MCI FNAD FDN FNAT FDN FNAL FDN CFTA NO CCFWDN CFN0 4 CFN1 6 CFN2 2 DFN0 4 DFN1 4 DFN2 4 DNDH NO MDID NO NDID NO MWFB NO TRCL 0 CRT0 00 00 00 00 CRT1 00 00 00 00 CRT2 00 00 00 00 CRT3 00 00 00 00 DAY0 DAY1 DAY2 DAY3 HOLIDAY0 HOLIDAY1 HOLIDAY2 HOLIDAY3

We have an Option 81C system and we are using VOIP for our outbound dialing to customers. For example, we can dial area code 313 phone numbers without any problems. When we attempt to create an ACDN with NCFW to a 313 phone numbers, we receive a fast busy. DCH messaging shows the call go out...

allenmac, That is what I was thinking. Thank you for the information :). Thank you, Olympus41

bhassell2000, We have numerous POTS lines that we are going to route 911 calls over. Thank you, Olympus41

We have just changed ALL of our inbound & outbound calls to go over our VOIP service. We are getting ready to submit a disconnect on our OLD (unused) PRI circuits. Before I submit the disconnect, I want to make sure it is ok that I set CLOCKING to FREE-RUN. Clocking is only required when you...

Yes, that is correct.

Hello, I would greatly appreciate any assistance. I have SPN of "1586123456#" (# will cover digit 0 through 9) programmed in my PBX. I have added "1586123456" to my NRS. I setup DCH messaging on SITE-A (making the call) & SITE-B (receiving the call). I see the call attempt on SITE-A DCH...