Search results for query: *

Hi I'm just wondering about some power requirements for our new switches. we received 6 they had a mix of power cables both 3 prong and twist lock. These switches will be used to power IP phones and Access Points. What my question is at what point would I need to use the twist locks for...

K Thanks

I see what you're saying, however if it was cross talk wouldn't it happen all the time on our lines? It's only happened 3 times and only on 1 day. thanks John

...sites. At the site they have a BCM450, with IP phones and 5 analog lines from the telco. Here's what they(the people at the site) said happened. * a single person called in through the outside lines, 2 of our outside lines rang ie ###-###-9900 and ###-###-9910 at the same time. 2 different...

I'm experiencing a similar behavior, what I'm wondering is if the person is receiving a vmail and a second call rings to vmail what happens? Does both vmail go to the vmail box or does or could one go to the general delivery? I'm currently checking into the feature setting option. thanks

Yes switches are configured properly, they are configured identically as the other site which works fine. I'm new to this part of the phone system. So all I know is when I connect the phone and it powers up, when the tone sounds. I slide my fingers across the 4 buttons, enter a long password and...

...vendors, so I believe there is something in the configuration that is causing it. The process for adding a phone is the same between both sites. * at the avaya tone swipe finger across menu buttons and add admin password to register phone. * 4 digit password to add phone and create extension...

...vendors, so I believe there is something in the configuration that is causing it. The process for adding a phone is the same between both sites. * at the avaya tone swipe finger across menu buttons and add admin password to regiser phone. * 4 digit password to add phone and create extion...

Ok, then the previous admin changed the console settings to something else, as I have no ability to see the boot sequence from console. The same device, cable and settings work with other switches in our environment. thanks

Thank, however that article you need console access, which as I mentioned console access had been disabled. Thanks anyways.

Hi, I've retired a Cisco Cat 2900XL and I want to reset it to factory default. My problem is, this is a switch I inherited, the previous network administrator had disable console access. line con 0 transport input none stopbits 1 So I've tried configuring a small duplicated network using a...

Hi I have paradyne bitstorm 2400 and 1020, and I'm having an issue with 2 sites. Is there any way to do any kind of diagnostics on the 2400? either on the device itself or the lines. Also any information with regards to the furtherest distance these guys can push. thanks John

Hi I need to know what I need to do to get the "configure vlan (vlan#) ip directed-broadcast enable" command available in my CLI. I need this for a wake on lan project, is it a license, firmware mgmt blade specific? thanks

Hi I have some Sun Solaris 8 or 9 boxes. Which are being retired and I need to sanitize the data. With other systems we're doing an over write of zeros to clear the data. Then format the disk and reinstall the OS. How would I do this on a sun solaris 8 and 9 servers? thanks John

thanks for your input, like I mentioned above, we will be setting this up at the branch and head office sides. We won't be on the TLS since that will cost $$$. This isn't a IT decision,but a business decision. I understand that this is not best practice and QOS should be configured across the...

At this point I need to provide QOS across the switch, since the business doesn't want to put out the $$$ for QOS on the TLS. I realize that by putting QOS only on our internal and branch infrastructure isn't likely going to do much. I'm being requested to do this by my management. Once this is...

Thanks tanderson3733 But here's my problem this is a small branch office 1 person, used to be 3. Connected to the head office with a TLS service. The internal network of the branch has only 1 vlan. Due to cost constraints the there's no QOS on the TLS and only 1 VLAN for that as well. In short...

Hi I need a little help configuring QOS in XOS. What I need to do is configure QOS for VoIP to have the highest priority on specified ports only. If anyone has any samples that would be appreciated. thanks John

Hi We're experiencing a weird issue with a couple PCs. The basic problem is the subnet they are on is allowed access to a specific site, all PC's on that subnet can access it just those 2 PC's can't. If we change their IP they can. What makes this a little weird is although we log the any drop...

I presume you have the VPN client installed. If so, you can check the desktop policy, this can be found diagnostics tool in the secure client folder. This policy is pushed out from the Checkpoiint Dashboard, the FW admin would need to modify the policy and you would need to update you the...