Thank you!
I've just been reading and that feature is not mentioned - but the software is a free trial so I've got nothing to lose.
Do you have a model of USB or wireless headset you would recommend? I've used Plantronics and Jabra headsets with Microsoft's OCS with good results.
Paul
Hi,
We've got a TDE200 and a TVM200.
I'm been experimenting with the "two way record" from a single button push - works well.
We've looked at automated call recording software for certain lines in our company - it is expensive.
Is there a way to automate the two way call recording so it...
Follow up...
Thanks to everyone, especially cwc3, for continuing to bang your heads against the wall on this one.
I gave up in the end. My main purpose was to get a separate fax system dialling out using H323. In the end, I installed a separate modem connected to an outgoing line rather then...
Tones sent back? Not that I'm aware...
COS - everything is set on 1 except TRS lock, which is 7
Under the actual port settings of the PRI card, the following are set on the Supplementary service tab. I wonder if any of these are having an effect?
COLP = No
CLIR = Yes
COLR = No
CNIP = No...
Short answer - yes.
Long answer - I have 15 lines on a partial T1. Lines 17 to 20 are the tie lines.
If you make a call out trying to use tie line to CO, line 17 and one CO line both light up for just a moment - then drop.
Paul
Well - it all the COS settings seem right and trunks look in order.
I think I'm going to start taking screen shots & attach them - something might stand out.
On the V-IPGW16, Shelf Proparty page, the Trunk Property is set to Private. Should it be set to Public?
Paul
I appreciate the amount of effort people have put in to solve this.
The Panasonic guys who first programmed this said it 'should' be working - good to hear you have seen this working between 2 other PBX's.
When I first started looking at this, 91 was in the first PBX's TIE table and I removed...
This is exactly how it is already set. I double checked all of it. All extension calls work fine.
From 91, dial 92 and 10 digits - rings once, a long pause, then a busy tone. This happens from all locations trying to call out from all other locations.
You said "Remember to set the number...
Well - my 222 says caller id features?
All the good stuff regarding Tie to CO starts on page 332 (section 1.30.1) - and yes I've been reading.
I can call all extensions no problem.
If I set a PBX code - my extension dialing stops working.
If I call anything other then an extension - I get a...
Interesting.
I setup a spare DID to go to 195 directly. Called it from my cell phone, it worked perfectly. 91 1 604 xxx xxxx dialed out as expected, call connected, no problems.
Hmmm - why will it not allow my tie lines to call out via DISA?
Paul
No - I cannot.
My local access feature on this PBX is set to 91, (92 on the second PBX, 93 on the third).
I call the DISA & hear the message. I dial 91 & hear a dialing tone. I dial the 7 digits - there's a pause, then a busy signal.
Paul
Apologies, the other work stuff got in the way, I can get back to this now.
100 is in use. I set it to 195, recorded a simple voice message, set security to none for testing.
I can call it from a tie line, hear the voice message, and then dial an internal extension. Works fine.
I cannot...
Thanks again guys,
CWC3 - Yes, I would like to connect to the other TDE & dial on thier nickel. I do not need a recorded dialing instruction message. Yes - our numbering is 1xx at branch 1, 2xx at branch 2, 4xx at branch 4 (branch 3 did exist, it went away).
I call other extensions in other...
Thanks guys,
I've gone to 5.3.2, entered 501 in the first slot. When I look at the extensions list - I can see 501 as OGM(DISA)
I added 5XX to 2.6.1
When I call 501 with the intercom button - I get a busy signal & 'reorder tone' on the display.
When I call 5019xxxxxxxxx or 75019xxxxxxxx...
Hi,
I have 3 TDE200's, all connected using the IP-GW.
How can I place a call from one PBX to another PBX using the TIE IP-GW connection but route the call outwards?
For example - if I could place call from PBX 1 to PBX 2 and then use PBX 2 to get to the outside world, it would save on long...
OK - it's fully working. Calls to extensions on each system work fine.
I need to work out how to dial an external number from Asterisk via the Panasonic (the panasonic will allow internal calls but not external)
I'm a bit busy at the moment, but when I get the chance, I should write up the...
Me too - but I spoke to a guy in Calgary who says he has it working 100% with no problems, (Asterisk to Panasonic IP-GW).
From what I'm reading, I 'think' there's a bug in the very latest h323 (ooh323) in Asterisk and that's what causing the calls to drop.
I might try going back a few versions...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.