Search results for query: *

OpenScape 4000 V10 Volume 4 IP Solutions Service Documentation Issue 39 Check 2.11.1 General Description The STMIX can be re-flashed in case the board is not booting or not becoming READY in RMX. The process can also be used to factory reset an STMIX board. All customer saved data will be...

Have you used the Assistant to update the loadware and OS of the STMIX ?

Yes, have you tried that ?

"-Is there no solution other than a hot line to send numbers directly to an analog trunk?" It might be worth a try - It may be that the HOTLN will not dial out directly but it will dial an extension so add 99 as a float number and forward it to the desired destination and test

Hi - you should address your request to the specific forum of Hicom300 which is for HiPath - https://www.tek-tips.com/forums/siemens-hicom.965/

Money - some customers have multiple sites (100 or more sites) that's a lot of upgrades and money to upgrade all the sites. They evolve and may move to OSV central platform - it depends - but end users will always require phones and if you can't get OptiSets/OptiPoints then the newer phones...

Yes, for instance you can add OpenStage 15 phones to HiPath 4000 Version 3 - The V3 system was released long before the OpenStage phones So, you have to make them 'backward compatible' to that system by setting the phone to be OptiPoint which the old system understands. Also if you use CP210 on...

Ha - Ok ! - I remember now - ! - sorry about that Here is the procedure for the Non-Display OpenStage 10 Plug in the phone to a working Digital Line 'The operating mode of an OpenStage 10 phone is changed via the 3 function keys. 1. Initially, all 3 LEDs of the function keys are off. Press the...

FAQ https://www.tek-tips.com/forums/965/faqs/7883

OK sorry about that - I was looking at it and seeing V10 - my mistake - good luck with upgrade !

OK - Maybe there is a recommended way But - I would start a new Duplex install and then go to site with the new processor and hard disks Shutdown the existing simplex - install the new processor, cables and hard drives and start up systems. You will need to generate an XML from the existing...

OK I understand - you are changing system from 4000 to OSV

My method - Probably wrong but it will work - would be to download a REGEN and other information from the Simplex and make a new Duplex off site. How are you doing the migration ?

Hold Down the Menu Button - it will ask OptiPoint or OpenStage mode The menu button is three horizontal lines

TRY Remove DFNN from COT and try again

Add TTT into COS of Telephone and COS of Trunk Retest

You can limit it - I've seen it in the iSDX Service Manual - which I've made avaialable for to download if you don't have it already. If you check out the 'Hicom' FAQ at https://www.tek-tips.com/forums/965/faqs/7883 you will get access to 'GigaTribe' and there you will see the Service Manual...

OK But it fills up the screen fairly quickly if you do A for all - I forget how to do it for individual equipment. So don't forget to turn it off ! :)

If the system is not connected to the outside and there is no working traffic then you could TRMB A That will give you constant traces, however it is processing intensive and as I said it should only be done on a system that is not working as a system. TRMB N will stop the command.

The REGEN file is completed as follows: STA-DEL: PAS:VEGAS/DATEI; REG-ANUM:A1; STA-REGEN:MYSTR,L3190000Z1234A00001,N,,,,,,ALL; - Put the ANUM number in there When completed then copy out from the hard drive (click on 'start local filetransfer') Theres a full regen macro file on GigaTribe...