Search results for query: *

i didnt want to use acd anyway since the users would have to logon to their set. all i want is a number that will ring all the sets. Unfortunately we have to use STE phones in that room so i cant even program a second line to the phone itself.

I have around 20 analog phones in a secure room. Each has its own DN, in addition to their own DN i would like to add each phone into a broadcast hunt group where a single DN would ring all the phones that arent currently in use. Is that possible without using ACD? i dont want the function to...

Thanks for the reply, for those who have this same problem you can look at page 997 of the Software I/O Administration NTP. Its under load 90. >LD 90 REQ PRT CUST FEAT NET TRAN AC1 TYPE NXX Thanks again GHTROUT for the fast reply.

West Virginia just resently added a new area code and went to ten digit dialing. I need to make sure that our local trunks are only allowed to dial out to local city codes. How do I print out what city codes are available after dialing 9 to get out? If any are missing how would I go about adding...

is that my site ID or my serial number? or are they both the same thing?

How do you find out what your site ID is? Is there a way to print it? Thanks for all the help

We bought new IP phone licences but i dont know how to install them. Any help would be greatly appreciated. Option 61c CS1000 IP Phones are i2001

I figured out the problem, turns out I'm just an idiot. What it was, I was trying to ping on a box that had multiple NIC's on multiple networks. Apparently it doesnt like that for some reason, once I tried it from a box with a single NIC on a single network it PINGed fine. Thanks for the info.

*bump*

I have a question about the i2001 phones. I have set a side a specific IP range and it would be great if I could do a multi Ping and see what addresses are used and which are not. However, whenever I try to ping an IP set it gives me a request timed out. Is there a way to change it so that the...

the thing is MCR wont work, there are no users, its going in to a dialogic card on a server. i think the easiest way would be for me to just use the short hunt option. its a little hokey, but as long as it gets the job done. They are all digital sets, 2616s

Thanks bigindian, but I read the post you copied that from and I get an error when I get to the STOR prompt. SCH8820 The DN entered is not valid for the GHT list. Why isnt it vaild? its an open DN.

I am trying to set up a list of 6 DODs that an 800 number can hunt to for an eNotify server. So I want the incoming call to be able to route to any of the 6 available lines skipping any of the line that are already being used.

I need to set up a Group hunt, 6 numbers with one pilot DN. and it needs to be availible 24 hours a day. I have package 120 installed and all of my group hunt lists allowed under system parameters. I just dont know where to go next. Thanks in advance for all the help IT1

ok I did the soft key trick and gave the phone a static IP and got it up and working. I still havent got the DHCP working yet, but I got the phone to ring and thats good enough for me. Thanks to everyone that helped me out with it.

How do I setup my DHCP server to do that (Windows Server 2003) or how do I change that setting on the phone itself. Also which would be easier to do just for testing? I just want to get this first phone up and working I can iron out the details later. Thanks, Luke USCG IT1

To my knowledge there is nothing coded on the set itself. I just pulled it out of the box and plugged it in. The firmware version is 0604D31. All it says on the display of the phone is starting DHCP and no other button will do anything. Thanks, Luke

What are the steps to setting up a new i2001 under TM? I have the phone plugged in to the switch and it comes up saying Starting DHCP but never gets farther than that. I have checked that DHCP is working with a laptop. Also the softphone on the laptop also works. I created a i2001 template with...

Great, thats not going to go over to well with the command, but hey what else can I do. Thanks for all the help. Luke

Yep, AC2. So would I have to change our NARS table? REQ: prt TYPE: dnb CUST DN 8 DATE PAGE DES CUST 00 DN 8 TYPE NARS NTBL AC2 CUST 01 NACT