Search results for query: *

This isn't supported until Communication Manager 5.2.X. The command you would use is list measurements ip dsp-resource gw and then choose summary/detail and the time period you wish to see. Example output below.... IP DSP RESOURCE H.248 GW SUMMARY REPORT...

9mmgeek, those values are probably IP addresses. The first one for example is an attempted RTP call between 64.5.121.45 and 64.6.120.37. Based on your description you want to chase out what these 2 IP addresses represent and make sure there is some connection in the ip-network-regions...

can you ping from the medpro to the other endpoint involved in the calls that you are trying to make? Say if you IP phone was 10.2.2.10 can you ping ip 10.2.2.10 board 1a02. If 1a02 was your medpro board.

The Linux command save_trans should work for you.

By chance if you are using internet explorer as a web browser make sure that the automatically detect settings box is not checked and try it again.

If you put https://ipofserver instead of http does this change what you receive?

Do you get that message immediately or do you get to click continue first and then the error occurs?

Can you get into the Linux level shell on the system? If you can try running ps -ef | grep autosat | nl This will tell you if there are a whole bunch of autosat processes you may have to kill some of them. If you see a lot of them you can kill them with one fell swoop if you run ps -ef | grep...

http://support.avaya.com/css/P8/documents/100059443 page 4 should have all of the information that you are looking far concerning mapd links and there message rates. Hope it helps you.

If you want to know how many you have total you can run statuslicense -v -a AUDIX and that will tell you how many mailboxes you are licensed for. You can run the system evaluation from the command line if you like /html/syseval/cgi-bin/web_syseval.pl it produces some html output obviously but...

dignoffo, that codec is a phone to phone codec and you won't see it show up when you status your station if you are using a medpro. When you status one of the stations on an active call you want to go to the next to last page, I would say page 7 or 6 but that varies with CM versions. One of the...

You should look at the traffic going form your CLAN to your remote phone to start. What usually happens is the phone will do its registration using UDP 1719 on the CLAN side and that's the first half and the second half is there is a TCP socket that is established between the CLAN and the phone...

In your example the PT is referring to modem pass through. Can you show how you have the location 5 media processor boards and codec set configured when it connects to the main site that you are trying to fax to and from. I have found that fax pass through seems to work more reliably than fax...

Can you post any errors you are getting on the PBX side of the configuration?

I would try to contact Avaya and ask about Insite Article KB01005254. Here is an excerpt from PSN 1010U The 9600 Integrated Gigabit Adapter (material code 700383771) generates heat that may be perceived by a user as unusual. The temperature is within the development specification and the product...

sawadallah01 did you try setting the speed and duplex using the setnic command? From Linux just run setnic -m 100F eth3.

VanZenden, this will work. I have seen other customers with a stack of G700's for example with 2 S8300's residing in the stack one being the main server and one acting as an LSP. You would just configure everything normally as far as the MGC list as you would if the LSP was at a remote location...

If you look at the maintenance web interface logs and select cron for the log type to view. Do you see anything that references a scheduled backup at the time you are setting it up for. You may want to try removing your scheduled backups and then just add in 1 schedule to run in say 10 minutes...

As long as you are sure you don't need the primary data going to the CAS, which is really the same data on the secondary port. Add a node name that has the IP address of your PC and on the ip-services form put the node name of your PC as the remote node and the port number you selected while...

Check out Avaya document 03-300430 page 186/187 it gives lots of suggestions that may help you out with the Bearer capability admin of the route patters and trunk groups involved in the call. Way too much stuff to paste into a post.