Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by donb01

  1. donb01

    Send Diferent number Cli

    I have to provide a full 10-digit number or the output will be the default number of the circuit (I think SPID is the buzzword), and the same goes if the number is not a DID on that circuit. Even though I "own" 5600 numbers spread across 6 buildings served by the same CO, if I try to give out a...
  2. donb01

    Send Diferent number Cli

    Also note that depending on the trunking you have there are restrictions. I have traditional PRI circuits in my buildings. I can set the PUBNUM of the phone to anything I want, BUT that number MUST be provisioned on the PRI I am dialing out from. So if my main number of my clinic is...
  3. donb01

    Openstage 60

    It's a hospital and set of clinics - I linger near the edge of the "chicken" wire :o) Don Bruechert, Voice Comm Analyst II CareTech Solutions @ Holy Family Memorial Manitowoc, WI, USA
  4. donb01

    Operating OS4KV8 system

    http://academy.unify.com has some online courses you can take for basic administration of the 4K. Don Bruechert, Voice Comm Analyst II CareTech Solutions @ Holy Family Memorial Manitowoc, WI, USA
  5. donb01

    Openstage 60

    In my previous experience, GA is a good thing to look for because I played with the bleeding edge for a while at the beginning and had experiences where I pushed out a new version only to have it pulled from distribution a week later due to problems. Now I always stay a few versions behind the...
  6. donb01

    Forward ACD Agent calls Externally

    What you have to remember about ACD is that it does not matter what the number of the HOST phone is - it matters what number the agent logs in as. I have several "Float" phones in my system, and what call center the phone gets calls from is determined by what login ID the person uses. So those...
  7. donb01

    Hicom 9006, STN PEN shows READY/DEP

    Also, is this a new problem on a working phone, or is it a phone you just connected? Some of the old Rolmphones were really pi$$y about reverse polarity on the cross connect. Some of them would sound like a tractor and you would know it right away, and others would be more stealthy. Don...
  8. donb01

    Hicom 9006, STN PEN shows READY/DEP

    Try DEA-DSSU:DI,PEN,1-2-3-4; (I can never remember if it is dashes or commas until I do it. Then do ACT-DSSU:AUL,PEN,1-2-3-4; Sometimes a PITA station will clear better if you turn it up/down by PEN instead of STNO. AUL doesn't just do an activate, it also does a reload on the station...
  9. donb01

    HIPath 4000 v6 reinstall by crash

    Did you try to edit it by hand or did you use the XML file creator for it? I might have the XML creator tool if it's not already posted here, but have to remember to look when I am at work. The one I have will be for V7 - not sure if there is any difference or not. Don Bruechert, Voice Comm...
  10. donb01

    HIPath 4000 v6 reinstall by crash

    There is a software tool that you use to create that "firstinstall" file if you don't have it - you have to put in all the relevant IP addresses, tell the system if it is simplex or duplex and a few other things. Then you can copy that file into the appropriate directory on your USB stick and...
  11. donb01

    HiPath v2 to V8 Upgrade

    I've heard June/July in the US as well. I am getting around it on a technicality. My contract renewal date is before V10 comes out and they will not renew my contract unless i'm off V7. This solves my immediate problem as I received no notice to budget for the upgrade early last year when I...
  12. donb01

    Delay Call Forward issue

    If I remember correctly, for mine on inside calls it will sound like a short ring with a beep at the end. I've never played with it from outside so not sure if they have a different experience. I can't imagine why it would change unless there were software updates installed or something, or...
  13. donb01

    OpenScape 4000 V7 with IPDA and SPE. Problems with NCUI board replacement.

    NPR means "not present". (I believe) regardless of software the system should still see the board in the slot. If it doesn't like something it will typically say WBT "wrong board type". Whether or not it works or not is up to the software. If you have never used the software before, remember...
  14. donb01

    HiPath v2 to V8 Upgrade

    I just found out I'm getting my upgrade to V8, so I should have time to budget for V10 :) Don Bruechert, Voice Comm Analyst II CareTech Solutions @ Holy Family Memorial Manitowoc, WI, USA
  15. donb01

    HiPath v2 to V8 Upgrade

    As far as I know the license upgrade needs to be processed either directly through Unify or through a reseller, depending on who your support channel is. Don Bruechert, Voice Comm Analyst II CareTech Solutions @ Holy Family Memorial Manitowoc, WI, USA
See more

Part and Inventory Search

Back
Top