Recent content by AvayaGrayBeard

I am installing a fresh copy of 11.1.2.2 on VMware now. I don't believe I've seen this issue but perhaps I worked around it without realizing it. Would you be willing to share some of the other major problems you're seeing? I am upgrading a client from 10.1 to 11.1.2.2 Thanks.

All the suggestions have been really helpful. I ran some trial upgrades on a fresh, isolated VM and it appeared to go well. In order to copy the backup data, I had to enable root access for SSH by updating /etc/ssh/sshd_config I also had to chown vmpro:vmpro and chmod 775 the backup files...

Thanks for the suggestions. Is it obvious when/if the restore goes sideways? It would be nice to know if it's successful before I turn it loose on users.

It's an IP Office Application Server running VMPro 10.1.0.5.0 build 2. Should I upgrade the 10.1 server to 11.0.4.5 first before importing the call flows and copying the WAV data? I wasn't certain if the WAV files would need to be converted to OPUS, or if that's a non-issue. Thanks again!

Is it possible to copy VMPro 10.1 configurations files to a new 11.1 SP2 instance? They would both be hosted on VMware. I have 150 users. Upgrading the server from 10.1 -> 11.0.4.5 -> 11.1 SP2, per the upgrade docs, seems complex and hazardous because of the Centos kernel upgrade. I'd prefer...

Does anyone know if the 6400 series works on IPO 11.1? I only need dial tone and the ability to dial extensions. I realize it's unsupported, but I have about a dozen 6408/6416 stations still in use with a IPO 10.1 system. I am preparing to upgrade to 11.1 soon and I wanted to make sure I am...

Does anyone have an example of a successful Valcom IP paging system they've installed on IP Office 10.1 or later? I've seen a few posts here, but nothing too recent. If anyone has a set of a equipment that they've found works well (or tips on what doesn't work well), I'd appreciate it. I'm...

ogTOKYO, Thanks for the suggestion. I re-upgraded my v2 control unit to 10.1.5 again, and it worked 100% as expected. So, fortunately, I didn't need to copy the phone file manually or even use the monitor to view the phone activity. I believe I read another post where the tech said that...

Thanks! I have multiple backups, so I'm covered on that. I did a little more research here, and discovered that even though the working/bin directory was set to C:\Program Files (x86)\Avaya\IP Office\Manager it's actually storing/reading from C:\Users\<userID>\AppData\Local\VirtualStore\Program...

Thanks. That's helpful. As it turns out, only "upload file" and "upload system files" are the only options. I assume either will work.

I had to run an emergency "Restore Binaries and Configuration" operation to downgrade a IPO 500v2 control unit from R10.1.5 to R10.0.2 after a bad upgrade. I want to re-try the upgrade now, but my IPO Manager Upgrade Wizard for R10.1.5 doesn't see the new firmware in the default working...

thread940-1787833 I upgraded a V2 control unit to R10.1.5 from R10.0.2 and ran into problems. The upgrade wizard threw an "HTTP request failed: 405 Method Not Allowed" error mid-upgrade. I rebooted and was surprised to see that everything worked fine except for my 9500-series digital...

Yes -- it's running as an application server. That was simple. Thanks so much for the help!!

I am about to upgrade VMpro from R10.0.2 to R10.1.5. Doe anyone have experience upgrading an OVA-installed VMPro? There appears to be more than one way to upgrade, and I'm not sure which is best. 1. Boot the ISO/CD on the existing instance and select the "upgrade" option. Not preferred...

Thanks. These are all great suggestions.