Search results for query: *

Hey, I set up some Polycom 6000's on my SV8100, and took some notes when I did it. I have 4-digit extensions, my Polycom's are all 4-digit extensions, and I have never had any problems. My notes say that I use 4.06 firmware I also use a custom bootrom that I made...I think I just display the...

SV8100

How did you send the diagram? I dont see it. OK, so in my case, the RCA jack from CH1 is going to go to the amplifier. That makes perfect sense. I'll install a digital station jack on the wall next to the phone switch, and verify that a phone works when plugged into it. Then we'll go from...

How did you send the diagram? I dont see it. OK, so in my case, the RCA jack from CH1 is going to go to the amplifier. That makes perfect sense. I'll install a digital station jack on the wall next to the phone switch, and verify that a phone works when plugged into it. Then we'll go from...

I have a branch office that is NetLink'd to the the home office. I have 2 POTS/CO lines at the branch office, and I need to disconnect them. Can I point a DID at the home office to an extension at the branch office? I know how to, I just haven't tested it yet. More importantly, how can I get...

Something like what?

From the manual: Installing an External Page System 1. Connecting to the CD-CP00-US: Connect an RCA line from the CN8 or CN9 connector on the CD-CP00-US to the appropriate location on the extension cross-connect block. 2. Connect the two-conductor station cable from the cross-connect block to...

I need some help installing an external paging system. I read the SV8100 System Hardware Manual on the PGD(2)-U10 ADP and I am tad bit confused. I have a functioning overhead paging system now, but its not hooked to the phone system. It consists of overhead speakers, an amp, and a mic. I...

I finally figured out the problem. I had incorrectly added @@@5551212 in the wrong area in an effort to keep employees from calling AREA-CODE+555-1212. When I did this, the system still allowed 7 and 10 digit dialing, but not 3 digit dialing.

I got it all working. I am routing 911 calls for specific set of VOIP extensions to go out the Verizon device. I also remembered to configure the switch so that if the 911 dispatch center calls back, it will ring on all the voip phones.

I know what you are saying about them not being true POTS lines, and at first I thought you might be right, because one of the sites is a Windstream fiber circuit that has Dynamic IP lines (SIP-to-POTS), but the other sites have the same problem, and they are other carriers. I know the carrier...

I forgot to mention...I have an issue with getting 911 out on that trunk. If I dial, #9, 028, I can dial local and l/d just fine, but as soon as I dial 911 it jumps to port 23. I don't know why it jumps like that. How can I stop that from happening?

System: SV8100 At my main site, I have a PRI and I can dial 9,511 or 9,611 just fine. I can also call either 9,911 or 911 just fine. Everything normal here. The problem is at my branch offices where they have CO/POTS trunk lines. When they dial 911, or 9,911, or 9,511 or 9,611 type numbers...

I like your idea of a button for 911. You're right about ARS - I have been messing with the simulator, think I have it, then it just flat out doesn't do what I expect it to do! Can I do a speed dial button that does: #9,028,911 ? This way, they dont even need to dial 911, the single press of a...

I have a remote branch office with just 5 phones - NEC VOIP phones that are registered to the SV8100 at my main site. Obviously, when these phones call 911, the wrong address is received by 911 responders. I have been trying to get a SIP trunk built between the SV8100 and a Grandstream HT503...

There is a simple and cheap way to do CDR / SMDR on the NEC. I had Tapit, and hated it. If you need fancy reports, this might not be for you. If you just need it for auditing, this might be just what you need. I do this method, and it works great for me! Here is the basics of it: (1) Setup...

I made a poor mans CDR using putty. I use putty to remote the the smdr port, and write it to a log. I then have a scheduled task that restarts putty after midnight, and names the file to that days date. Works great!!

I had same problems years ago. The best networking guys, NEC engineeers, and wiresharks, couldn't figure it out! The crappy work around from NEC was to change it from net link to ccis. Anyway, a while later, I figured it out! I figured it out bc when we setup our failover internet connection...

I have an SV8100. I have never worked on one before nor have any training. All my past experience is on an Avaya Communication Manager 1.1 I had my NEC dealer add a SIP license to the system. He said it will work with 3rd party gear. I am trying to register an ATA....specifically a Cisco...

Wow, I haven't messed with this in forever. I don't work at the company that I was doing this at anymore. Someone else actually wrote the port listener for me that was dumping it to the database. I wrote the .asp pages that displayed the data in web pages. The apps would have been specific to my...