Search results for query: *

lugerlover: Do you know how to access this message so that I can either delete it or change it?

I have Norstar NAM voice mail that is playing a strange greeting that someone recorded. I have checked the following greetings and can't find the recording: Gen Delivery Mailbox 1000 CCR Tree's Greeting's 1 thru 8 The only time this happens is when a call goes to a mailbox that has not been...

Thanks to everyone who responded. Here is how it I made this work. An in-house PRI between two Norstars requires a T1 Cross-Over cable. You must use the Sl-1 protocol with one side set as a master and the other as a slave, and then you must not have any numbers which overlap if you are going...

Has anyone ever networked two Norstars together? I am having an issue making the system sync with each other. Particulars: Both 4.1 software Both have separate PRI's with 2 way DID service Want to pass digits from one system to other for internal calls. As an example one system is 50XX and...

LD 27 is used for something else now, I have no idea as to when Nortel changed it, but I don't know of another Load which supports the feature set that LD 27 had.

Defintely use 9 as AC1

Option 61 in Europe that has sets that are TLD with an NCOS of 0, which points to an FCR table. Also within this PBX are sets that are UNR or CTD also with an NCOS of 0, FRL's match NCOS's. All RLI's have a FRL of 0 I have checked the NTP's and they gloss right over this programming. My...

oops you are correct it is not a 97 it is a 12 Dual PRI Card. The book gives a very poor description of the functionality of dip switch number 8 it might be the co that I am connecting to. Thank you for pointing that out to me.

Installed two cards both with the correct daughterboards, but neither of them is functioning. Here is how they are programmed. Loops are 38, 39 and 44 I have only shown one of the 3 d's but they are all the same. Did I miss something? ADAN DCH 4 CTYP MSDL GRP 1 DNUM 4 PORT 0...

All Phones are TLD, AC1 is 9

I have a PBX overseas that is having an issue dialing the sequence of 9001. Here is the Code Restriction Block entry's, I can't figure out which one of these is blocking the calls from accessing. Help! CRNO 0 INIT ALOW DENY 156 CRNO 1 INIT ALOW DENY 111 156 00 ALOW 003 004...

Using the TTY port to access the system does anyone know of a way to control a phone to dial a certain sequence of numbers so that I can verify the correct routing paths?

Thank you

How do you set the Diff Serv Bit in the BCM?

Anyone know of a good maintenance vendor in Toronto, they have to be an authorised distributor?

We have symposium express running GRTD. All is working well except that the callswaiting billboard is reseting to 0 after about 5 minutes rather than being cumulative for the whole day. Does anyone know how to fix this? I've already installed all the latests peps.

I am looking for the correct pinouts for the M2250 console, for the DB25. It isn't in the NTP's and the one in FAQ's isn't correct so don't suggest that I look there. Thank you.

Thank you both of you are correct, you only get the General Delivery Mailbox if it is enabled.

I doubt that he would be able to hear everyone with 16 people on the line. You might point out that to support a conference call that big you would need to have alot of trunks. Thats what conference bridges are for, sell him one of those and tell him to go with the Norstar.

You can't reset the SEB-II modem without special software that only SEB provides. The software is big bucks. Why don't you just get a USR modem for about $100, the SEB is useless if you don't have the monitoring software anyway. There are some vendors who will reset the SEB for you, last time...