Search results for query: *

I would like to set up a VPN gateway using the PDM. As my company is using the ADSL modem to connect the ISP. When I want to enable the "enable outside" of vpn pptp, it displayed following error. Error : [ERR] vpdn enable outside Can not enable vpdn on the same interface as PPPoE. How can...

Could the Cisco 4000 upgrade to c4000-is-mz.12.1? What series about it? 4000 or 4000-M? (68030) processor = 30Hz CPU? Does it support ADSL? Thank you for your helping! Cisco Internetwork Operating System Software IOS (tm) 4000 Software (XX-J-M), Version 11.1(12), RELEASE SOFTWARE (fc1)...

Where can I download the c4000-is-mz.12.1? As my IOS was corrupted! Thank you victorjob@mail.hongkong.com

Thank you very much! What command can I test the speed in cisco router? I refered to my book that serial could support greater speed at 115,200Kbps.

Thank you

If I used the DB60 cable to connect back to back router. does this DTE and DCE DB60 only support 2Mb? so slow... Thanks

Thank you routerman if the serial interface only support 2MB. How does it support T2 or above? What unit does clock rate calculate? Kb ? Thanks

I implmented two routers as follows, but they are very slow. 192.168.3.0-Cisco1601R <static route> Cisco2501-192.168.0.0 Two segments 192.168.3.0 (A) 192.168.0.0 (B) When I move a file from segment A to segment B that it was very slow. How can I improve speed of my two routers? I have been...

Cisco Pix 520 is greater than Cisco 515E?

How can I do? thanks cisco1601R# 2w5d: %SYS-5-CONFIG_I: Configured from console by consolesh run Building configuration... Current configuration : 786 bytes ! version 12.2 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service...

I could not view the sh ip route, how can I do? cisco1601R>sh ip route Default gateway is not set Host Gateway Last Use Total Uses Interface ICMP redirect cache is empty cisco1601R>

What different about switchport multi vlan 1 and switchport access vlan 1 ? Can I add port of fa0/9 to vlan 1 and vlan2?

Thank you very much for fmonteiro. Who have the Cat2926T to sh version or flash? As I saw many images on CCO for 5000/2926T, Which should I take? How can I upload the new image or delete the error image again? As I only saw the following unrecognized messeages in 2926T's concole port...

Why my catalyst 1900 could sucessfully upgrade to cat1900.537.bin only? I could not complete the process when I ugraded from cat1900A.8.01.00.bin and cat1900A.9.00.04.bin. My Tftp server only display this message of transmit error while sending to 192.168.0.19. the connection is reset by remote...

I see, if I want to share the internet using NAT, i need to get the 2514 router on 2500 series. right?

I have solved this problem. My DB60 cable is DTE/DTE. I have changed the new cable, that is ok.. Thank you for your kind helping.

I used the a cable of http://www.citac.edu.hk/adv/b2b6ft.jpg One side connect to 1601R One side connect to 2501 What cable or adaptor should need to add? Thank you

Thank You Cisco1601R sh controllers serial 0 ------------------------------------------------------------ cisco1601R#sh controllers serial 0 QUICC Serial unit 0 idb at 0x264B5B8, driver data structure at 0x264CFDC SCC Registers: General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x0...

Finally, is it possible? I also want to know, thanks use a cisco 2501 router to share adsl. Is it possible???? This router only has one ethernet port, but i can get another 2501 router and connet them both, this way i have on ethernet for adsl and other to connect to the hub.

Which cable should I take? Cable company : http://anthonypanda.com/prodlst.php?cat_id=1 Thank you very much!!