Search results for query: *

Thanks that did it. I had to also set MSXC. Again I am amazed at the quality of the support in this forum. It is as good as any tech support around..

The error in the book says (CDP data block (CDP-LIST)does not exist. Does anyone know what it takes to add CDP to the switch? thanks

This is the best forum going. I was able to get the 0 to work by changing the NCFW to an extension. Now my problem is if the calling user doesn't hit any key when dialing into the main number it goes to a message that I don't know what it is. What dicates where the caller will be...

We just had a phone system put in and when a user dials 0 at the main greeting it goes to fast busy. The revert number in the greeting is 0. thanks

I am having this same exact issue. I tried to set the PRI card to a tie line but got SCH0520 error. SCH0520 NI-2 basic call only supports COT/DID route. When CBCR =3D NO and IFC =3D NI2, route type has to be either COT or = DID, TKTP =3D COT/DID. This drove me nuts for about an hour...

Another piece of info. When I dial the ACOD and a local/long distance number from a telephone on the Nortel network it forwards to the operator also...

I have a system where a Cisco router/Voip network talks to an Option 11 switch thru a DTI/PRI card. Basically the Voip cisco phones can use the trunk on the Nortel to call the Nortel phones internally or make local/long distance calls. This system has worked well for a couple of months using...

We have 9 analog lines coming into a Norstar MICS. We only need 4 analog lines. We want to disconnect the lines at the telco and remove them from the Norstar. We own Norstar Remote Utilities. How do we take the lines out of the phone system from the GUI. The Analog Lines are on...

Thanks very much for the info. Right on as usual with this forum!!!

I have been told you can see what digits are going in or out a tie line... I thinking I am sending certain digits to the voicemail system but I am not getting the desired response. Someone told me I need to use LD80... How can I track what digits that the voicemail is getting (it is an...

So if the voicemail system is 4218 and the extension of my voip phone is 4332, and if I have created a Meridan Mail box of 4332, what digits does the Meridian mail system expect to see to let a caller leave a message? thanks

I have a few E&M ports from a Cisco router hooked to a Nortel switch. My IP phones off the Cisco router can make calls, receive calls, etc. What I am trying to do is to get the IP phones to use the meridian mail. I am have a hard time getting the voip extension to automatically rollover...

Thanks for the great response. This forum is great. Obviously I am new to the Nortel stuff. It seems like the Nortel manuals are very technical and in depth but lacking on the real world situation stuff. This forum has helped a lot with that. I hope I get to the point where one day, I...

9 is DN 9 TYPE NARS NTBL AC1

We have a phone switch that is starting to integrate with a Cisco VOIP system that is connectected through TIE lines. So if I have an Extension 2100, how do I tell whether that goes over the TIE, stays internal to the Nortel, etc. thanks

As always the greatest replies in this forum. Thanks very much TTY 2 was disabled..

I wanted to access an option 11 switch from the LAN that had a dumb terminal hooked to it. The dumb terminal worked fine. I took the dumb terminal off and hooked a cable from an AUX port on a Cisco router to the 25 pin connector that was hooked to the dumb terminal. Reverse telnet from...

What communications package should I use to access my phone switch remotely? What type of protocol should I set it up as? I know you can use procomm, are there any freeware packages? thanks

I am a rookie with our Option 11 switch. I have become the defacto admin. I need to set up a new phone. How do I find how many ports (TNs) are still available to add extensions on the switch. I was told by the last admin that we were almost out of ports for new phones. I have plenty of...

What is the command that is similar to a Crtl-C is the DOS enviroment. I am doing LD20 PRT DNB and I have too much info coming across the screen. So I want to stop it and start again. thanks