Tracking digits going into a trunk (LD 80?)

[twmoody]

I have been told you can see what digits are going in or out a tie line... I thinking I am sending certain digits to the voicemail system but I am not getting the desired response.

Someone told me I need to use LD80...

How can I track what digits that the voicemail is getting (it is an internal card in the meridan)?

Does it use a lot of resources?


thanks

 

[cmawbey]

LD 80 provides a valuable trace facility which gives a snapshot of call activity on the system. The following commands can be used to monitor and trace calls:

LD 80

. trac 0 xxxx (where xxxx is a DN) this will give information on any call present on the DN or indicate idle, it is possible to enter the ACOD of a route as a DN and this will result in an indication of the condition either idle or busy of every trunk member of the route.

. trad l ch (where l is the loop and ch is the channel of a particular digital trunk member) this is useful when after tracing an ACOD of a digital route, ISDN, DPNSS or similar, you may then trace any of the channels marked busy to check their call status.

. trak x x (where x x is a TN on an Option 11 Meridian) this will give details of any calls on the TN and if it is a digital set the status of every key.

. trac xx x xx xx (where xx x xx xx is a TN on a Meridian 21 and above) this gives the same information as the command above.

. trat 0 x (where x is the attendant number of a switchboard on the Meridian, if only one switchboard is on site then this will be 1) this will show the status of all loops on the switchboard and details of any calls present on them

Colin

 

[twmoody]

Thanks very much for the info. Right on as usual with this forum!!!

 

[BigBMark]

you can also use enhanced trace in LD 80 i.e.

entc c u xxxx

where c u is the TN (on an option 11) and xxxx is the time you want the trace command to run.

after that you must start the trace by entering the command

gotr


This is a good alternative to trac and trak when you need a realtime view of what is going on. the trace updates you whenever there is a change in status of the TN for as long as you have specified with the time parameter xxxx.

Andre

 

[jesseeu]

Can you post exactly how you typed in the time parameter. It seems like anything I try gives me a TRA306 or TRA101 error.

Thanks,
Jesse

 

[phonejack99]

The command shoud be entered as --

ENTC L S C U ( or C U for an 11 ) HHMM. HH can be any value between 0 and 23. MM can be any value between 0 and 59.

Remeber that if you exit LD 80 the switch will stop the trac regardless of the timed value.

 

[mrgauth]

I have tried this entc command in 80 on several different switches and I get the same message in all of them. I get a TRA305 saying that you need to have multiuser turned on in LD 17. What in the world is it talking about. I have no clue 1) what multiuser has to do with anything, and 2) where in LD 17 it is talking about.


Thanks

 

[phonejack99]

Under gateopener OVLY
Prompt Multi_User
Enter ON

 

[olympus41]

I keep getting those erros also, TRA101. PhoneJack, can you run through the steps:


Under gateopener OVLY
Prompt Multi_User
Enter ON

Thanks,

Olympus

 

[phonejack99]

What Rls. of software and which type of switch?

Post teh exact entry and the error and we can go from there.

 

[olympus41]

Nortel Meridian:
VERSION 2111
RELEASE 25
ISSUE 08 +

I print out the TN 28-10-0-0:
TN 028 0 00 00 <- The printout shows TN 28-0-0-0 for
TYPE COT some reason.
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 0
RTMB 0 15
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD
P10 TRC LOL
TKID


I do a trace on 28-0-0-0, and get error TRA101:
>ld 80

TRA000
MARP NOT ACTIVATED

.trac 28 0 0 0

TRA101


I also try doing a trace on 28-10-0-0, and get error TRA101:
.trac 28 10 0 0


TRA101
TRA101


I have tried doing a trace on 11 0 0 9 which an ext is assigned to and I still get the TRA101 error:


.trac 11 0 0 9


TRA101

 

[ArchibaldJCox]

A couple of things:

You have an option 11. Instead of using L S C U (i.e. 11 0 0 9) use C U which would be 11 9.


Also, I believe "trac" is used for DN and "trak" and "trad" are used for trunk TNs. (trak for EXUT trad for digital trunks)

so try the following in LD 80:

.trak 28 0
.trad 0 xxxx (0 is customer number, xxxx is the extension of the phone)

-Archie

 

[cmawbey]

i have a script that will do this for you

if you want a copy send your email to

colinmawbey@bigfoot.com




Colin

 

[DDionne]

From the Opt 11C manual:
TRAC c acod List route number, type and status of each trunk for customer c
TRAC c dn Trace calls for customer c Directory Number or Local Steering Code dn
TRAC c r m Trace calls, customer c, route r, member m
TRAK c u Trace calls associated with this unit
TRAK c u k Trace calls associated with key k on specified unit
TRAC x yyyy Trace using customer number as DN
TRAC xx...xx DEV Print auxiliary data
TRAC zzzz Trace using TN of the set to be traced
TRAD loop ch Trace DTI or DLI calls, channel ch of loop
TRAT c a Trace calls, attendant a of customer c
TRAT c a k Trace calls associated with key k of attendant console a for customer c
TRAO c u Trace attendant calls, this unit
TRAO c u k Trace attendant calls on key k
TRAO xx...xx DEV Print auxiliary data

From the M1 manual for Opt 51C or higher (most of these can also be used on Opt 21 or higher):
TRAC c acod List route number, type and status of each trunk for customer c
TRAC c dn Trace calls for customer c Directory Number or Local Steering Code dn
TRAC c r m Trace calls, customer c, route r, member m
TRAC l s c DSLx Trace calls on Digital Subscriber Loop x (0-7)
TRAC l s c u Trace calls associated with this unit
TRAC l s c u k Trace calls associated with key k on specified unit
TRAC x yyyy Trace using customer number as DN
TRAC xx...xx DEV Print auxiliary data
TRAC zzzz Trace using TN of the set to be traced
TRAD loop ch Trace DTI or DLI calls, channel ch of loop
TRAT c a Trace calls, attendant a of customer c
TRAT c a k Trace calls associated with key k of attendant console a for customer c
TRAT l s c u Trace attendant calls, this unit
TRAT l s c u k Trace attendant calls on key k
TRAT xx...xx DEV Print auxiliary data

Also available on Opt 11C or higher running software rls 19 or greater - the Enhance Trace feature:
(**Please note that Multi-user Login must be ON**)
DALL Disable all enhanced trace commands.
DIST n Disable the enhanced trace operation.
ENTC l s c u t Enable the enhanced trace command for a TN.
ENTD l ch t Enable the enhanced trace command for a digital trunk.
FITR Get information about the enhanced trace function.
GOTR Begin enhanced trace commands. This command starts the trace
operation specified with the ENTC and ENTD commands.
STPT Stop the enhanced trace command.

DD