Search results for query: *

Hello There! Sounds like you have night mode working the way you want. I will assume you used D:L 1-1 for each of the co's . . . During day mode you need to set call intercept extension to the VM Extension (probably 165) ... Set the Intercept to number of rings you wish ... and it should work...

Oh well. Guess they will just have to deal with it! <g> Thanks for all the help and ideas! Rick

Thanks! Will attempt this ASAP.

I know the newer phones have a Day/Night button but do you need a new software release as well?

Hello, Started having a problem this AM and to be honest don't readily see why. I have, during day operation, and intercept of 4 rings to the voice mail extension 165. The ports on the TVS-50 are set to immediatly answer. Today on several occasions, person that answers phone out this am, the...

Hello, Yes ... I have programmed VMT many times ... I see from allot of tech articles that they refer to this as VMT and VTR ... sorry for the confussion ... We are using a VMT button. And all works well as this is a small office ... Problem we run into is during day operation if someone get...

Hello and thanks for the reply. > Solution 1: You can swap the DND solid led and the FWD > blinking led in programming under additional function (on > newer versions?). > Solution 2: Newer systems (-5 and above?) have a preset > call forwarding setting under station setting # 1. I am running...

Hello, I have a 1232 and TVS50. I recently added the TVS50 and all seems fine. I am getting one complaint. During the day when the system is not in AA mode individual extension are sent to the voice mail using the FWD/DND buttons. Folks are complaining about having that FWD/DND buttons light...

Hello, I did this same setup (except TVS50) this past week. I used night/day service button's. In night mode set D:L 1-1, for the correct co's, to the voice mail port. In day mode set the, I beleive it was intercept, to the number of rings you wish to have it go to the AA. And do not forget to...

Thanks for the response ... We ended up assigning two -one touch- buttons ... this works however the lights do not light and they are forgetting to change it from day to night (781 on second button) or night to day (780 on first buttone) as there is no visual indicator to nudge them ... any...

I have a KX-TD1232 -2 and would like to add a night service button. It looks however like this release did not support a night service button? We are using KX-T7230 phones. Thanks - Rick

I just did this and made my own device. If you need help give me a call at 330-534-7552. Rick

Thanks. Checking another card would be the next logical step wouldn't it! <g> I have a VM card on the way for this unit. I will know then if it's the ACS or the card. Does $245 for a replacement card sound reasonable? It's the upgrade to R5 as well Backup/Restore/Remote Access. Thanks, Rick

I tried the other slot ... I've powered off so many times and tried again it's not funny ... is the card junk then or can the card be reflashed? Thanks, Rick

Are there any obvious things to check, other than a properly seated card, when you get the &quot;invalid card&quot; response when trying to perform a backup (#124) on ACS R4? It is the silver card that is -labled- &quot;Remote Access&quot; and has (&quot;Backup, Restore, Upgrade&quot;) written...

I was heading in that general direction. Have not worked with Lucent/Avaya much and the previous owner of the business, were the system is located, -claimed- that they had a night bell with just the equipment that was there. Abd if course -claimed- it stopped working when I made programming...

PS - I meant for Night Bell ... Thanks Again, Rick

I've been told that I can use the TPU-15a with the Partner ACS without any special devices, is this true and if so how? Thanks! Rick