Search results for query: *

Hi What if you have 3 ELU32 and only a one LIM system.

Hi Here are the pin outs La10, Lb10 - incoming 4-wire line (ind 0) 4C26, 4C28 - 2-wire line (ind 0) La20, Lb20 - outgoing 4-wire line (ind 0) 4A30, 4A32 La11, Lb11 - incoming 4-wire line (ind 1) 4C18, 4C20 - 2-wire line (ind 1) La21, Lb21 - outgoing 4-wire line (ind 1)...

Hi You should be using SAM 3.7 Service pack 3 build 8. The NIU1 should be firmware revision R17a. If you are using NIU2 the firmware should be R6a. If you copy files using Xmodem it can take up to 1 hour to copy 1 mb of data at 9600 baud via a modem. You can raise the speed on NIU to 38400 baud...

Hi Fisbi can be used on BC12 NIU2. It has been tested on 28 Lims using HDU7/1 with 2x190mb partitions REL1 and REL2 and safety disk HDU7/1 with 190mb partition. The safety disk reloads the system. Flash ram was not used as its capacity is to small. " The proof of the pudding is in the eating "

Hi The partition created is less than 64mb(about 60mb) so it will work on all flash ram of 64mb and above and is enough to fit size of INL about 20mb. It is not good practice to create a new system from an INL extracted from another system. You should always use an original INL from the vendor.

Hi Connect to niu with niux enter the following commands You need Sam 3-7 SP3 build 8 and BC12 INL SP6 /***** Create INL with NIU2 and Flash ram **********/ niux > atinfo niux > atfmt 0 niux > mkfs /DEV/AT01 3C00 3B00 100 niux > fsck /DEV/AT01 niux > fsinfo niux > mount /DEV/AT01 /USR1...

Hi Please send all operator prints etc, opcap opcgp opctp optsp opddp rodnp:rou=all,tru=all rocdp:cust=all aspap:parnum=all

Hi After you format and create the file system and mount the flash disk or HDU you should use MDDT from SAM 3-7 sp8 to create INL. Make sure you have the latest firmware on NIU2 or NIU. Also make sure you are not using old NIU/1 boards. There are problems with old firmware and hardware on NIU...

Hi I tried to forward the thread but it does not work. here is the info from that thread Sam Tool Box 3.6 SP3 don´t support NIU2 with flash ata. The commands for SCSI-Disk are: scfmt 3 LL mkdev /DEV/SC31 231 mkfs /DEV/SC31 FFE0 1000 400 mount /DEV/SC31 /USR1 I try to translate it for NIU2...

Hi The correct prom for BC11 in U.K. is RYS 102 642/1 R5A. This is for TLU76/2 ROF 1375338/2 and makes the board R6A.

Hi You need program USS "upgrading support system" from Ericsson. This shows you the revision of the relevant card and what prom is needed to upgrade it to the correct revision for the BC release of MD110 you are using.

Hi Change SIG on route to 111100000030 and see if that works you can always change it back to 511100000030 .

Hi The latest version of SAM is 3.7 SP3 Build 8. It fixes lots of problems in SAM sofware suite.

Hi There is some good info at this link to check if NIU can see HDU7 using NIUX commands. Although it refers to creating INL some of the NIUX commands are relevant. http://www.tek-tips.com/faqs.cfm?spid=806&sfid=2717

Hi Do you have the cable between the niu and hdu plugged into the correct position. The Niu has an ATA port that is never used.

Hi Ammendment You can use SYECP; but it does not help for past year only for future years.

Hi You can use SYECP; but it does help for past year only for future years.

Hi Change the first bit on SERV on TL11 route to zero. This should stop call waiting.

Hi If you take LIM 2 out of service and do CNPIP:UNIT=DTM; it will show you if DTM is active in LIM 3. If that is the case and you can dial out in the LIM's that have no route members present then it could be a problem with the power down of LIM 1. I dont know how easy it is for you to test this...

Hi If you only want basic call functionality with QSIG then BC7.2.2 is O.K. You are right that E1 ISDN will be O.K. But if you want full QSIG functionality then minimum is BC9 and even at this version you can have problems depending on the type of PABX you are interworking with.