Search results for query: *

Problem solved! It seems that the problem was the wrong seeting in at the Client NIC. I had to set it manually at 10Mbps. Now it seems to work...

I´m now have the same Problem! I´ve got an 8 Port NBII with 11.4 SW/NBDPE-DW Software Installet! In the PPPoE Service Menu aren´t any entries! Have someone news about this issue?! Greetings from Germany-Berlin Robert D.

I´ve got a Netbuilder II (CEC 20, F.W. 2.7, Software v.10.1/Complete Protocols)Router with an Ethernet AUI Card! I connect the Router Card via a CenterCom 210TS AUI Transciever to a netgear 100 Mbit netgear switch (autonego). The Netgear Switch shows a "Link", but when i Ping from a client to...

Does anyone know where i can get the Software Version 4.70 for a Contivity Switch 1500/1510!? The latest Version which i can download is 3.60! But i think when i want to use PPPoe, DHCP-Client on WAN interface (as Private)... i need at least Software Ver. 4.5 or above! Is that right!? Does...

Many Thanks for your replay! Thats right! When i connect my 100MBit WS the Link LED is on! Now i have another question! I haven´t got the console cabel! connetction via Telnet doesn´t work, because the Switch cut the connetion! Is there a way to configure the switch without buy an console...

i finally brought an used 28115 ADV! After booting up, the Display shows "Operational:RUN! No Errors are displayed! But all LED´s on the ports are green! I can´t connect to the Unit! Does anyone know what this means when all LED´s leave in green!?

Hi! I´m searching for the newest Firmware Version for a BayStack 28115 Switch, Version 2.1.1.6 And i´m also searching for the Windows Backend Admin Software! Does anyone know where i can get the software!?

Hi! I´ve got an 3Com Lanplex2500, and i´ve tried to update the Firmware! That Failed! When i now boot the Switch, the Message "Flash EPROM Checksum Failure"! How i can install an new Image or can boot the switch over the Network! I´ve tried the workaround from the Manual, which...

Yes x.x.x.1 is the IP-Adress of every port! All IP-traffic hast to flow from 1,2 and 3 to port 4, which is attached to an Linux-Proxy Server! Another problem i had post for a while is: When i attach the NBII to a PC with a X-Cable there are problems withe pinging the router, or other PC´s! A...

Hi! I´ve got an 4-Port NetBuilderII, and have problem with routing! I´ve got 4 Subnets, each on every port: !1 = 192.168.1.0 !2 = 192.168.2.0 !3 = 192.168.3.0 !4 = 192.168.4.0 The goal is to route all traffic from each Port only to the Port 4 (WAN)! The other subnets don´t have to be...

I need another help with building filters.. I´ve got 4 Cards: Port 1: 192.168.1.0 Port 2: 192.168.2.0 Port 3: 192.168.3.0 Port 4: 192.168.4.0 I want, that the router only routes from all Interfaces to the Interface !4 (192.168.4.1- connected to the internet router)! I tried the following...

I´ve make another trie with ataching the pinging Station over a hub with a 1:1 Cabel! There i dont have any losts! It seems to bee a problem, with the direct connection over a crossover cabel!

Yes i changed the Transciever and Cable too! Everytime the same problem.. i´m still confused

Hmmmmm.... I´ve pinged a whole night to the 10BaseFL, without any losts I only have problems with pinging to the 10Base2/AUI cards... I can´t belive that all cards are damaged.....

Hi again.. I´ve got a 4-Port NBII with CEC20 Bord! ..with the following boards: 1x 10BaseFL 2x 10Base2/AUI 1x 100BaseFX All interfaces work fine, only the 10Base2/Aui bord has problems! I have got a lot of packet losts, a average of 50% are lost by pinging! I have 4 other 10Base2/AUI boards...

Does anyone know where i con get the 3Com transcend Manager Software?! Thanks for helping Greetings from germany

Hi, from Germany! I´ve got a 8-Port Netbuilder II with a CEC CPU-Board 12 MB Ram)! Can I install in this chassie an DPE40-Board!?!? Are there any know Problems with this board!? I need it, because i want to install a 100BaseTX card,..but the CEC-Board doesn´t support this card,....not...