Search results for query: *

Have you got in the /etc/system already contains one of these entries? Use whichever value is larger for that setting. Before modifying /etc/system, use the sysdef command to view the current kernel parameters. Add the following lines to /etc/system and reboot for the settings to take effect...

What do your log /var/adm/messages say? regards Phil

New features have been added for systems using RBAC and BSM under Solaris 8. These features allow the pfexec to directly update the audit logs and widen the scope of auditing, providing finer grained auditing. Document Body: Top RFE #4398611 pfexec should directly audit its use. This RFE...

Hi The following command is used to set the serial port characteristics: nohup sleep 999999 < /dev/cua(a|b|c|d) & /usr/bin/stty 'option' < /dev/cua(a|b|c|d) Please note that these commands work with all stty options on ports A&B. ON ports C&D, only the speed can effectively be set...

white-paper: http://sunsolve.sun.com/pub-cgi/retrieve.pl?doc=fwpaper%2F26919&zone_32=26919 http://docs.sun.com/db/doc/816-0211/6m6nc671h?a=view http://www.hmug.org/man/1/netstat.html

First of all, I would like to describe the general structure. gld is generic lan driver and gld, in turn, uses the services of the specific lower level device driver such as elxl or iprb. SEND gld ----> elxl (or iprb) --> send out on wire RECEIVE data on wire --> elxl (or iprb) --> gld Ipkts...

The minimum operating system requirements for Smart Card Reader operation are Solaris 8 with Patches 108909-12, 109354-14, 109695-03, 109887-13, and 110457-05. Smart Card on TS8 HW 12/02 Workaround ------------------------------------- * Configure smart card using Smart Card Admin GUI...

Hi Ken What for an A1000 configuration have you select? Daisy Chained? Have you labled the LUN's? You can do the following: Reset the old configuration in A1000 1. Power the A1000 down and power system down 2. Remove all of the drvies but the first one (far left) 3. Remove the battery...

hi jmiturbe Sorry, I can't help you! But I found some links, perhaps they can help you: http://aa11.cjb.net/sun_managers/2000/10/msg00075.html http://docs.sun.com/db/doc/806-3204/6jccb3ga6?a=view http://dbforums.com/arch/128/2002/7/424026 greetz Apricot

Listed below are a few examples of how it is possible to use the vxprint and vxdisk commands to find the amount of VxVM disk space: 1.) To find the total amount of VxVM disk space in a particular disk group: # vxprint -g testdg1 -dF &quot;%publen&quot; | awk 'BEGIN {s = 0} {s += $1} END...

# vxdg -g diskgroup free

UFS logging and Disksuite's trans metadevice logging serve the same purpose which is to store the UFS transactions in a log before the transactions are applied to the file system. However the two have some differences as listed below: a. The Disksuite logging is available with the Solstice...

The default soft limit for the resource that controls the size of an application data segment is 2Gbytes. If the application needs to allocate more space, then the shell can be used to raise or remove the limit entirely. For csh use: % limit datasize unlimited or for sh, ksh $ ulimit -d...

http://sunsolve.sun.com/pub-cgi/retrieve.pl?doc=ffaqs%2F01406&zone_32=01406

Looks like if the smart card reader driver can't &quot;power up&quot; smart card HW, it tries to clean things up, but in the process it releases a mutex it does'nt own.

To test an operating system's upgradeability to Solaris 2.6 or above, a utility called pfinstall which performs a 'dry run' install can be used. The pfinstall command was first available with Solaris 2.6, 5/98. pfinstall can be used to prescreen an OS for potential errors that could prevent...

# vxdg free

RAID 5: 1. Create a disk group using Volume Manager with a minimum of 4 disks: # vxdg init datadg disk01=c1t1d0s2 disk02=c1t2d0s2 disk03=c1t3d0s2 disk04=c1t4d0s2 # vxassist -g datadg make vol01 2g layout=raid5 2. Create a mount point for this volume: # mkdir /vol01 3. Create a file system...

http://support.veritas.com/ or STEP 1---------------------------------------- We will encapsulate the primary root disk using vxdiskadm. vxdiskadm Volume Manager Support Operations Menu: VolumeManager/Disk 1 Add or initialize one or more disks 2 Encapsulate one or more...

The default factory settings for the Sun Fire V480 system are input-device=ttya and output-device=ttya. If you would like to use video/graphics and a USB keyboard, you will need to change the NVRAM settings manually (reference the V480 Admin Guide). To perform initial system boot up, use ttya...