Search results for query: *

Hi - no you're right it is not hearing the 3. I just tried extension 23 and it said "your call can not be transferred to extension 2." Does that mean I have a bad VM module?

Oops - I have a bug. Not sure if I caused it though. If I dial extension 13 from an inside line - it goes to that extension, rings, then I get the voicemail. If I call in on an outside line, then select extension 13 from the automated attendant, it pauses then says "your call can not be...

Thanks for the help TouchToneTommy. It is working great now. I just did the backup and it did back everything up. A few years ago, I remembered seeing Solid State drive replacements for sale on ebay and on a website - a guy that ran a Partner phone store had figured out how to swap in an SSD...

TouchToneTommy: It works with DND on or off.

You're correct about the naming - I mis-spoke. The new module is Partner Messaging R6 with a four port card in it. And you were also correct about the port assignments. I corrected them and it works now. Thank you very much. I have another question: If I get a backup card for this PM R6...

Hi everyone, My Partner Mail VS R4.1 is giving me a steady yellow light now. I swapped the hard drive out and am still getting that yellow light. I know how to format the drives and correctly put the data and directories in the drive for it to work - I've done it twice before successfully -...

I solved this by removing line 2 from the phone and voicemail setups. It works fine this way. Thank you everyone for the suggestions. Regards, Dale

Thank you WikiTech - that is what I'm going to do very likely. but next post gives me an idea... Dexman: If that is the case that the caller ID is on a daughter board, then I could get another Partner II module cheap and swap the daughterboard - and maybe not loose the settings if the daughter...

Hi Budbyrd: I'm not getting any caller ID on the phones with line 2 but I am getting it on line 1. I tried swapping the incoming lines and the result is the caller ID from phone line 2 that is now going into the 206EC line 1 DOES show caller ID info. If I put that same incoming line back into...

Telecomboy - thank you for the tip about #301. I will look it up in the manual and try to skip over line in port 2. I agree it is weird, but it isn't the 206ec card like I would have expected - I've swapped it with a brand new one twice (I have two NOS spares). I wonder if the 206ec right next...

Hi Dexman - The phones are all set to ring immediately. I had already checked that. The caller ID info comes through on any phone line connected to "Line In" port 1 - but not any phone if I move the line 1 wire and put it into "Line In" port 2. I think that pretty much erases the likelihood...

Hi Everyone - I'm hoping you can solve this. I have a Partner II R4.1 system and two 206EC cards connected to all MLS-18D phones. Line one "IN" is connected to the top port of the first 206EC module. Line two "IN" is connected to the bottom line-in port of that same module. Suddenly I noticed...

NEAXMAN: When you first open the back of your phone, look at the circuit board. See two black edge connectors? There is a flex circuit that plugs into those black edge connectors. This same flex circuit wraps around to the other side of the circuit board (where the buttons are). This is called...

Hi - I think your 34D phone has a defective mylar "flex circuit." When you press buttons on your phone, those buttons press on this flex circuit to complete the circuit for that pressed button. These flex circuits get internal shorts. When that happens, the phone acts just like yours is...

Thanks for your feedback Dexman. The reason it would not always be preferred is if someone wanted to default the system to resell it or move to a different location. Another reason would be if the "auto reload" file was defective and caused problems after an earlier restart. This forum is...

Assuming an ACS R7 system has lost it's programming, does this automatic restore occur 100% automatically so that the phone system is restored an operational like nothing happened once power is restored? Also, is there a way to block it so that it will not restore on a one time basis? Last -...

Excellent! Thank you - Kinneman

Thank you For the explanation and instructions TTT. I want to be sure I know what the backup steps are for, so: Is the first step intended to write over any backup that may be stored inside the system's memory with the default settings? And is the second step intended to default any backup...

I'm looking at an ACS R8 processor but it has not been defaulted and probably has an unknown admin password in it. How can I reset this back to factory default and remove any admin password?

Excellent - works exactly like I hoped. Thanks Dexman!