I have a CS100M with a cassidian E911 system and ALI databse. Currently I have to use my cable records database to input my records into ALI. Is there a better way the PBX can provide me with the correct information for the ALI and Cassidian System. How about internal ESN data?
Thanks
Configuring Secure Local Menu through Full DHCP
Password protection is enabled during Full DHCP configuration if the
SECUREMENU parameter, or the PARTSECURE parameter are present at
the end of the S4 part of the Full DHCP string. If neither the SECUREMENU
parameter, nor the PARTSECURE parameter...
Good Morning,
I need to know what the S4 DHCp string is on the DHCP server. I am trying to set up the full dhcp securemode and and partsecure.
DHCP Secure Mode The IP Phone follows the menu lock configuration
received from the Full DHCP string
• if SECUREMENU is present, you are prompted to...
We have found where to remove it. It was only visiable in Element manager under the ESN Data Block. GHTrout was right that is has to with Autovon. It is ols programming left over from a previous version.
Here is from memory. This is the ESN data print out from LD 86.
AC1 9
SDGT 0 OVF
SDGT 1 IMM
SDGT 2 PRY
SDGT 3 LOC
SDGT 4 RTN
SDGT 5 LOC
SDGT 8 LOC
SDGT 9 LOC
AC2
Hello out there,
I have a CS1000E that I am working on setting up BARS and the prevoius software programming is using SDGT under AC1. I need to remove these SDGT from AC1 and no where in the NTP's does it show how the remove these. Can anyone tell me how this done.
Thanks
All the patches are up to date, INI'd the PBX and did reload. The 0's whould show up in groups of four.
example: 0000 or 0000000000000000
but always in groups of four no matter if on the same line. How/where would check the LOF and LON and the prompt SEND OFF?
Thanks
No, this was going on before that. At the time I thought the DCH's where also causing this problem. Now my DCH's are good and I am left with this problem. I really do beleive it has something to with calls though. Thru-out the night it runs clean because noone is at work, but as soon as the day...
Sorry for not getting back for awhile, have been on leave. Multi-user is turned on and there is only one connection to the paddle board. The rest are connected to a QSDI card.
Yes, I agree with your assessment of the CNIP after doing some reading. The TTY I am using is on computer with serial connection using Putty. This connection is also going over a Cat 5 cable about 25 Ft from a TTY Paddelboard. What is weird is that I did disconnect this cable from the...
Thanks, but what am I looking for as far as health. I know the higher the health number the better. I stat the health and everything looks good. I do however see a CNIP 0 9 1 disabled and there is no pysical port for it and it will not enable because of no port. This may be the problem, but how...
Hello All,
I have allot of "000000" output to my TTY's at random. This seems to be more prevelant as the day goes on as calls increase. I already disconnected all my TTY's one at a time to see if was a TTY issue and it's not. I suspect something with CNi or 3PE since in LD 135 it has OOS...
I do this all time, there are NXX's in your local NPA that will be long distance. To solve this use your DMI table entry that will add 1NPA. Then Program an RLI to route to your long distance trunk with the DMI entry programmed. The end user will not even know he is dialing long distance.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.