Search results for query: *

Good Day, I am currently having the following issues with a clients 450 BCM: initially with every onther install that i have ever completed there are never any programming steps required besides installing the MBM and assigning the start DN: xxxx .still not excepting DTMF ??????? please advise

@cook1082 - Resolved, 2 rings was the cure. Thanks!

This is standard and already has been completed, still the same affect.

Please advise on the following: 1. Call ID has been allowed on 5 lines. 2. AA is also allowed on 3or4 of those 5 line 3. Caller ID has been allowed on user set and Active line. 4. Tested the POTS line with CLID set direct connect w/o PBX works fine When inbound call come is it only displays...

Hello - Please advise on the following: Phone Set 1220 Key 1 DID Line Appearance (555-5555) Key 2 Appear Ring Answer DN - (5512) Key 3 Intercom (5557) Key 4 Intercom (5557) 1. If there phone set is not active it will go to voicemail 2. When Key 1 is active on an inbound Call it will not go...

Ok Gent's, seems as if we are making some forward momentum - My only last concern - With DRT Turned off - end user forward incomming call to an internal ext with DND the call will continue to ring as well as bounce back to the sender for "Callback" until voicemail kicks in. Can call back be...

Just a little follow-up able to change prime on the taget line - the phone rings to the voicemail after 4 rings. Not familiar with the acranim DRT, please explain - thanks in advance for your attention.

My setting are already defaulted to FNA to voicemail DN after 4 rings - results still the same.

Set have DND active, if enduser dose not pick up the call it will forward to reception - How do I cancel this redirection? any insight would be helpful, as well as how can the call just go directly to voicemail with out call forward no answer?

Noted, Thanks guys. Ploted it out and sure thing an Analog trunk Should be pluged into and analog station.

Correct Analog trunks are connected to analog trunks.

Just in case - NOTE: Both systems are facilitated with analog devises i.e. ATA breakouts and ATM MBM ;)

Gents - Has anyone had any luck trunking the 2 devices, If so please share the wealth of knowledge. Current Setup 1 BCM50r3 DN's - 2XXX 1 BCM450r1 DB's - 3XXX Licences Applied on both systems - check/configured Routes & Destinations Codes / Line pools - check/configured I am trying to firgure...

Dasheen (Programmer) 6 Jan 09 20:39 did u program the private rec'd digits on the BCM? Yes I have amended the matching DN's to the the private recieve digits of the BCM tnphoneman (Vendor) 6 Jan 09 22:07 MWI capabilities on the Dchannel? Yes MWI has been activated on Dchannel...

Dailing plan Has been set on both the CS1K and 450 as CDP with 4 digit DN's.

tnphoneman The NCOS - exactly the same way as the already Active option 11c Release 25.40, essentially the BCM will replace the 11c. Any addtional information will be greatly appriciated - Thanks.

tnphoneman Prior to my post the PNI has been set correctly - Both sites are set to 1, any other suggestions or something that I may have overlooked? Thanks in advance for your attention.

Wondering if there was anyone that can point me in the right direction. I am working with a BCM 450 and CS1K RlS 5, and I have all the pre - requesits programmed for the cs1k and 450. 1. 450 to CS1K - ext. to ext dialing both ways via sip - ok 2. 450 to CS1K - DID dialing via sip both ways -...

MCDN Keycode - has been applied CP DN has also been applied to Message Center options Exteranl autodial 450 PBX VM DN (7000) ok - Login confirmed 1. Also are there any other changes that must be configured in Message center? 2. I am having a problem with CS1K CP not able to dial out to 450...

Wondering if there was anyone that can point me in the right direction. I am working with a BCM 450 and CS1K RlS 5, and I have all the pre - requesits programmed for the cs1k and 450. 1. 450 to CS1K - ext. to ext dialing both ways via sip - ok 2. 450 to CS1K - DID dialing via sip both ways -...