Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. pronei

    IPO SE 9 w/ 9608 SIP Phones in Error Mode

    I'm primarily a CM engineer, I work with IPO when needed. This phone had a beta load of SIP firmware from my CM/SM environment. Was simply hoping the same firmware would work, didn't know the 96x1 SIP phones weren't supported yet. Seems weird that they are not.. yet the the old Nortel...
  2. pronei

    IPO SE 9 w/ 9608 SIP Phones in Error Mode

    LOL, still not in even in SE 9 SP2?.. ugh.. http://www.linkedin.com/in/neil74/
  3. pronei

    IPO SE 9 w/ 9608 SIP Phones in Error Mode

    I have a IPO SE 9, using 9608 SIP phones. The phones register and can take calls ok, but are in error mode (Triangle w/ bang/exclamation in middle). I get no features on the phones at all, just basic 3 call appearances. Any Ideas why the phone is not getting its full feature set...
  4. pronei

    Beginning a list of Caveats for IPO 9, please add to them!

    FYI: Do NOT use the upgrade wizard on a Brand New Out of Box IPO 8.x to upgrade to 9. Plug the SD Card directly in to your PC and use SD Card Re-create. If you fire up a new 8.1 with intentions of putting 9 on, make CERTAIN you do NOT make a phone call on the 8.x or you WILL have to have an...
  5. pronei

    System Manager & IPO 9 Issues

    So I've integrated IPO 9 to SMGR 6.3 FP3. I've found the following: 1. Standalone IPO Mgr ceases to work, you must do EVERYTHING through SMGR 2. SMGR User Logins (The email address of the user in SMGR) can't use .-_ or any other special char's as it puts the SMGR login name in the "Name" field...
  6. pronei

    Setup Network to have All IP Offices respond to Manager PC

    Have any of you ever setup a customer's network so Broadcast traffic reports back to main site? Basically, what customer wants is when their Manager PC sends out a broadcast on 255.255.255.255 that ALL the IPOffice's respond back. Remote sites are all connected to Main Site where the main IPO...
  7. pronei

    Get Rid of / Remove the 'To VM' softkey on incoming calls

    Yup, though I'm deploying 900+ IPOffice units for a customer and their users are not to have VM boxes and the customer wants the "To VM" softkey gone.. oh well http://www.linkedin.com/in/neil74/
  8. pronei

    Get Rid of / Remove the 'To VM' softkey on incoming calls

    So, as I suspected, no way to actually get rid of "To VM" softkey only a work around to not allow anything to be written to the user's VM directory (That shouldn't exist in the first place as I did NOT check the Voicemail on, but that's another story). Come on Avaya, lets get it right.. simple...
  9. pronei

    Get Rid of / Remove the 'To VM' softkey on incoming calls

    To VM soft key on incoming calls. I need this softkey gone, is this possible? How do I get rid of it? IPO v9.0.0.0 build 928 w/ 9611G H323 http://www.linkedin.com/in/neil74/
  10. pronei

    Factory Default 4621sw

    There is no *, It's stuck in a hard coded VLAN (used phone from another location that was moved) and apparently the: SET OPSTAT SET PROCSTAT SET PROCPSWD in the 46xxsettings.txt did not allow for * during boot. I didn't know if there was a keypress combo that can be done during startup to CLEAR...
  11. pronei

    Factory Default 4621sw

    Does anyone know how to reset a 4621SW during the boot sequence? I need to CLEAR the phone as it has bad VLAN settings, but can't find a way to get into the programming menu during boot. I can't MUTE CLEAR# or RESET# as the phone is stuck looking for DHCP in a non existant VLAN. Is there a...
  12. pronei

    Bogen UTI312 Station Paging

    Solution - To Setup Station Paging using a Bogen UTI1 or UTI312 Multizone Pager: Parts: 1 Biscuit Block with RJ11 4 Wire Jack 1 330 Ohm 1/2 Watt Resistor 1 Standard RJ11 4 Wire Line Cord 1 Cat3/5/5e/6 Cable 1 RJ45 Mod Plug Instructions: 1. Program IPOffice Analog Extension Port as Paging...
  13. pronei

    Bogen UTI312 Station Paging

    Does anyone have a wiring diagram on how to connect a Bogen UTI312 to a Station Port on IPOffice. I'm fairly certain you have to use a 330ohm 1/2 watt resistor, just not sure how to wire it all up. http://www.linkedin.com/in/neil74/
  14. pronei

    USB_Initiator Download

    Thank you sir! http://www.linkedin.com/in/neil74/
  15. pronei

    USB_Initiator Download

    I've already opened a ticket with Avaya IT, but was hoping that someone has it available and could put it up for download quickly. http://www.linkedin.com/in/neil74/
  16. pronei

    USB_Initiator Download

    I already tried that, it's not there http://www.linkedin.com/in/neil74/
  17. pronei

    USB_Initiator Download

    Anyone have a temp drop box where I can download the USB_Initiator? I've got to get this UCM installed and the file can't be downloaded from Avaya right now.. ugh.. http://www.linkedin.com/in/neil74/
  18. pronei

    Issue with VM Pro

    Or in a customer's case that I recently ran into, the Preferred License was present, but the Essential License was missing. Preferred requires Essential be present to function! After 90 days the phone system got rebooted and went to lock out! That was fun! :/ http://www.linkedin.com/in/neil74/
  19. pronei

    IP Office 7.0 Message Button

    That got it Bas, it was in intuity mode. Thanks http://www.linkedin.com/in/neil74/
  20. pronei

    IP Office 7.0 Message Button

    IPO v7.0.27 w/ VMPro When a user presses the msg key on their set (95xx or 54xx set) it is asking for ext & password instead of just logging directly in to VM. Is there a way to make it log in to VM without asking for ext/pwd? Each user has their own unique Source Number of Vxxxx (where xxxx...

Part and Inventory Search

Back
Top