Does anyone have a wiring diagram on how to connect a Bogen UTI312 to a Station Port on IPOffice. I'm fairly certain you have to use a 330ohm 1/2 watt resistor, just not sure how to wire it all up.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Bogen UTI312 Station Paging 1
- Thread starter pronei
- Start date
smokinjoe2938
Programmer
600 ohn resistor
acss sme acis sme acss cm 5.2.1 acss cm and cmm acss aura messaging.
acss sme acis sme acss cm 5.2.1 acss cm and cmm acss aura messaging.
intrigrant
Systems Engineer
> Page 6
Set the alog station in IPO to IVR.
Know your product and become a Pro
Set the alog station in IPO to IVR.
Know your product and become a Pro
-
1
- Thread starter
- #4
Solution - To Setup Station Paging using a Bogen UTI1 or UTI312 Multizone Pager:
Parts:
1 Biscuit Block with RJ11 4 Wire Jack
1 330 Ohm 1/2 Watt Resistor
1 Standard RJ11 4 Wire Line Cord
1 Cat3/5/5e/6 Cable
1 RJ45 Mod Plug
Instructions:
1. Program IPOffice Analog Extension Port as Paging Speaker (Example Ext 135)
2. Create Short Code
Code: *60 (Or whatever you want)
Feature: Dial Paging
Telephone Number: 135 (Or whatever you made Ext in Step 1)
Line Group: 0
3. Use Cable & RJ45 - Crimp RJ45 to Cable - White/Blue on Pin 4, Blue/White on Pin 5
4. On other end of cable attach White/Blue to Pin 2 & Blue White to Pin 3 (or center pair of other size jack)
5. Connect the 330 Ohm Resistor between the 2 center pins on the biscuit block (Creating a resistance bridge)
6. Connect Line Cord to Trunk/Page Port on Bogen UTI
7. Set Switches on Bogen UTI:
Put the Port Selector Switch in Center Position (Page Port)
Put other Switch on VOX
You will only be able to page using Short Code or Button configured as Dial Page, you CAN NOT dial the analog extension directly.
That's it, you should be able to page now! If you're using a UTI312 you may need to crank the volume on the ZX3 Modules for it work correctly.
Parts:
1 Biscuit Block with RJ11 4 Wire Jack
1 330 Ohm 1/2 Watt Resistor
1 Standard RJ11 4 Wire Line Cord
1 Cat3/5/5e/6 Cable
1 RJ45 Mod Plug
Instructions:
1. Program IPOffice Analog Extension Port as Paging Speaker (Example Ext 135)
2. Create Short Code
Code: *60 (Or whatever you want)
Feature: Dial Paging
Telephone Number: 135 (Or whatever you made Ext in Step 1)
Line Group: 0
3. Use Cable & RJ45 - Crimp RJ45 to Cable - White/Blue on Pin 4, Blue/White on Pin 5
4. On other end of cable attach White/Blue to Pin 2 & Blue White to Pin 3 (or center pair of other size jack)
5. Connect the 330 Ohm Resistor between the 2 center pins on the biscuit block (Creating a resistance bridge)
6. Connect Line Cord to Trunk/Page Port on Bogen UTI
7. Set Switches on Bogen UTI:
Put the Port Selector Switch in Center Position (Page Port)
Put other Switch on VOX
You will only be able to page using Short Code or Button configured as Dial Page, you CAN NOT dial the analog extension directly.
That's it, you should be able to page now! If you're using a UTI312 you may need to crank the volume on the ZX3 Modules for it work correctly.
- Status
Similar threads
