Hi all,
We currently have an Avaya Communication Manager and System Manager, release 10, in operation, which is all functioning well. Additionally, we have Avaya Workplace for both Windows and mobile phones active, and it's also performing well.
However, I would like to import a list of...
Thanks, I cannot remove the station in System Manager or Communication Manager, object in use, please try again later. Also after a busy out station I cannot remove, same message.
Look liks a bug indead. For now I make another extension for the user and try a reset system 4 after office hours...
I've tried busy station 5101 and a status, function still active.
Tried another trace li trace 5101/14 when phone is not logged in but same result, function still active.
Thanks again, I've already tried the li trace 5101/14, very good function the +6 trace :-)
I've tried it again but no results.
I've logged 5101 in by Avaya OneX so I can also see this button and can click on it but it stays green.
I realy don't know if this is the correct button. User contact...
Thanks Sean655 but when the user push this button, nothing happen.
I've tried it in OneX Communicator, but nothin happen when I toggle or click this button.
Hi all,
System: Software Load: R017x.01.0.532. Avaya CM and 9608 H323 phones.
One of the phones on a remote location has no ringer, status station says: Ring Cut Off Act? Yes
The person on the remote location is a nog technican and didnt want to change something.
I've no H323 phone on my...
Hi,
We’ve an IPO 11.0 server edition with PRI.
Situation (fictive numbers):
Internal number A = 6000
Internal number B = 7000 this number is twinned to mobile phone 012345678, that works fine.
When A6000 calls to B6000, A sees B and 7000 in the display but when B answers on his mobile phone, A...
Thanks @ZeroZeroOne
The Signalling configuration is the trick.
The adaption configuration won't work, still get the +0123456789 but doesn't matter, the signalling works.
Thanks!
Hi,
We've a CM 7.1 with Session Manager and SBC's.
Our customer has about 400 locations and many stations need a caller-ID.
Until now, we use the "private numbering" in Avaya, that works fine but the "private numbering" table is limited for about 500 entry's so this table is full now.
The trunk...
Hi,
We're using Avaya CM 7 with SIP trunks and 9608 IP Phones, H323.
There is a problem with answering incoming calls.
When a station receive an incoming call, station will ring, when we pickup the headset, we hear a dial tone and automatic line 2 is selected. Line 1 is still ringing. We've...
You can configure a extra digit for "go to step 7" so callers can push that digit to go directly to step 7.
Otherwise it is not possible, system is waiting for response digit from step 2.
Hi,
We've a working solution with Avaya Equinox within CM/SM environment, release 7.
We use Samsung phones with WIFI and VoIP dialing, it works fine.
There is a problem with some Point Mobile phones. When there is an incoming call (VoIP) and this phone answer the call, the volume in the first 10...
Thanks for your response.
The proxy sel rte in the “display locations” is empty, nothing configured. In the trace we can see the call is routing to trunk 1, and trunk 1 is the Session Manager in our configuration.
We’ve make a test, and put there a route pattern to another trunk (PSTN) and make...
Hi,
We’ve a problem in our configuration, Avaya in VMWARE environment, Software Load: R016x.03.0.141.0 with Session manager.
The ARS access code is “0”. So if we want to dial to 0612345678, we’ve to dial 00612345678.
With our 9608 H323 phones, it works fine, but we’ve also some 9608 phones with...
No you can't use the feature button for EC500, because you won’t activate the EC500 function for the 96201, but for the 96300 (in my example)
So you have to set the 96201 to console permissions, and the Ec500 enhanced code.
You can configure a button with autodial function, autodial *6196201...
Hi,
We’ve the following configuration:
A hungroup with a couple of users, on page 2 I’ve configured an announcement with a delay of 0 seconds (for test)
When I do a direct call to the huntgroup extension, I can hear the announcement fine.
But when there is an incoming call, to a (virtual)...
There is a easy solution, set the station to Send All Calls, station does not accept any call 😊
Yes it is possible, but not in a good manageable solution, only in a creative configuration.
You can add 4 stations, for example 96300-96303
Put those 4 stations in a coverage answer group.
Then...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.