Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: bzakk
  • Order by date
  1. bzakk

    I have a new number 4644 I can't call from outside???

    yes I can dial it internally, I have it in the default partition which is the same as the 38XX. These numbers are coming in over a SIP trunk to a Nortel CS1000. The CS1000 is sending the 4XXX numbers the exact same as the 38XX. I don't know how to setup a translation. I have a phone at my desk...
  2. bzakk

    I have a new number 4644 I can't call from outside???

    I have 38XX already in the callmanager. I want to add the first 4XXX number. I built the phone but I can't get the Call Manager to accept the call. Do I have to tell it That 4XXX is a new number. If so how?????
  3. bzakk

    CC License Manager service stuck in starting mode

    CCMS SU_04 CCMS SUS_0401 CCMS SU0_402 LM SU_04 CCSMU SU_04
  4. bzakk

    CC License Manager service stuck in starting mode

    CC License Manager service is stuck in starting mode and will never start. If I set the service to manual and reboot I can start the service just fine if I manually start it. But as soon a I set it back to automatic and reboot it will never fully start on it's own. Does anyone have any ideas?????
  5. bzakk

    Integrate Nortel CS1000 with Call Manger 6.1.1 through SIP

    Does anyone have any documentation on how to integrate Call Manager With Nortel CS1000 using SIP?
  6. bzakk

    How do you send DNIS across Tie Trunks

    I am working on an IVR system that needs to see DNIS when it recieves a call. Does anyone know how to send DNIS across TIE or DID Trunks.
  7. bzakk

    ip phone programming

    He just changed the tn that the phone is pointed at, he didn.t do any programming changes.
  8. bzakk

    Having trouble with CBCT channels going into lockout.

    Rout 3 is master and Rout 1 is the service rout. ROUT 3 TYPE RDB CUST 00 ROUT 3 DES CBCTMTR TKTP CBCT NPID_TBL_NUM 0 VTRK NO NODE DTRK YES BRIP NO DGTP PRI ISDN YES MODE PRA IFC NI2 IPUB --- SBN NO PNI 00000 SVRT 1 NCRD NO CHTY BCH DCDR NO ICOG IAO SRCH...
  9. bzakk

    Unable to Transfer Calls

    Make sure that TRNX and EXTT are set to yes in the NET portion of the customer data block in LD 15.
  10. bzakk

    Having trouble with CBCT channels going into lockout.

    I have a NI2 T-1 going to a IVR system using CBCT trunks. I cannot get the channels to stop going into lockout. I have rebuilt them every way I could think. Could the IVR cause this if it isn't ready for the call??? The DCH gives me this message. CAUSE: #44 CAUSE: #44 - REQ CIRC/CHAN NOT AVAILABLE
  11. bzakk

    How to block a local number?

    Just block it in ld 90 with NXX just like you block long distance with NPA. Instead of entering NPA enter NXX and use NXX 222 then it will ask you if you want to DENY and then put 5555. It is the same exact thing as blocking long distance.
  12. bzakk

    Remote Mini Carrier

    They work fine you don't have to really do anything different. I have a couple of them and the only time I have trouble with them is when the t-1 goes down..
  13. bzakk

    SDL2110 REASON 1

    I have the correct cables but maybe there is a bad one. I will replace all of them tonight and see what happens.
  14. bzakk

    SDL2110 REASON 1

    I am having trouble bringing up a new IPE. This IPE is a Fiber remote that is working off of an existing multi-IPE fiber box. The download will start but it will fail with a SDL2110 Reason 1. I have changed out 2 controller cards and 2 network cards. I know the fiber is good because there is...
  15. bzakk

    Call Pilot Reporter not talking to Call Pilot

    How do I go about doing those steps? I am not familiar with a host file or adding Network to the DCOM.
  16. bzakk

    Call Pilot Reporter not talking to Call Pilot

    I have installed Reporter but it wont talk to Call Pilot. CP manager and My Call Pilot works fine but reporter is giving me the following error. 1 Wed Oct 10 05:45:27 PDT 2007 [80004005, Unspecified error, Description: Unspecified error CDSJob::Run(): CP Server ping failed, Source: CallPilot...

Part and Inventory Search

Back
Top