Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Cardine

    Audiocodes C450HD-TEAMS

    Picked up three phones but the firmware they are running is very old (.066). The docs talk about using SSH but the phone doesn't allow it, nothing in the settings menu... Any one know the "old" way to upgrade these phones?
  2. Cardine

    failback of mitel phone through firewall gets one-way audio (Phones in teleworker mode)

    Valamagules, that did it! Thank you very much, saved me a lot of aggravation with the firewall! Thanks again!
  3. Cardine

    failback of mitel phone through firewall gets one-way audio (Phones in teleworker mode)

    Two Internet connections voice going out WAN2 with failover to WAN1. WAN2 fails and phone(s) FAILOVER to WAN1 no problem, everything works. Service restored to WAN2 and due to Mitel keepalive messages, sessions are not cleared on the firewall so the MBG at the remote thinks it's still talking...
  4. Cardine

    Mitel 6910 and 6905 Phones menu during bootup

    Do we have the ability to access the settings menu by holding down a set of keys during boot? Can seem to find anything on this on the mitel site...
  5. Cardine

    MIVCR 9.1 SP4 Recording a EHDU or Call Forward

    Blitz, my assumption is you have this working, are you using trunk side to station side? My ports are late binding, and they do record all call EXCEPT calls that are tromboning in and then out of the system Alphamann, i'll take a look at the docs, im not adverse to upgrading the system....
  6. Cardine

    MIVCR 9.1 SP4 Recording a EHDU or Call Forward

    Blitz66 thanks for the response, however neither of the suggestions work. it appears that a tromboning call (either call forwarded or EHDU) does not get reliable picked up b the MIVCR. I've tried just about everything i can think of, trunk side,station side, direct vs indirect. Below is a log...
  7. Cardine

    MIVCR 9.1 SP4 Recording a EHDU or Call Forward

    Has anyone found a work around or way to do this reliably? Basically need to record trunk side (or station side) and record a call that is forwarded out of the system. - using SIP Trunks. stumped.....
  8. Cardine

    BCM450 R6 Dropping alot of Packets

    OAm im connecting direct. I've tried diconnecting it from the network and plugged my laptop into LAN1 or LAN2 but the problem is still there - packet loss OAM works fine as described above.
  9. Cardine

    BCM450 R6 Dropping alot of Packets

    yes did a reboot... Never seen a NIC act in such a manner, gonna try an SU update see if anything changes....
  10. Cardine

    BCM450 R6 Dropping alot of Packets

    Wondering if anyone else has seen this issue when even pinging the BCM it drops packets or the response is in the 100's of MS, sometime 1000's. I've even went as far as disconnecting the LAN and plugging directly into LAN1 or LAN2 but the problem is still there, when I use the OAM it works...
  11. Cardine

    Cisco SPA5XX on MiVoice Office / 5000 Screened Transfer anyone?

    Can't seem to get Screened transfer to work , I'm hoping someone else has run across this? All other aspects work - Blind Transfer works. Essentially you press screened transfer and dial the party, but when you try and join the two calls it drops. "transfer failed" Anyone?
  12. Cardine

    Mitel STT replacement

    Since mitel stopped supporting the STT, has anyone found an alternative, one they have actually tested and got working using Nupoint?
  13. Cardine

    spa508g remote worker MWI not working

    Blitz, thanks for the reply, so I found that setting and it worked on my lab system, but the production system still doesn't work...now I'm really stumped, what else could I be missing??? Keep in mind this is a remote set...I'm officially stumped
  14. Cardine

    spa508g remote worker MWI not working

    So basically I'm wondering if anyone has set this up before and what Outcome they had, i've messed with it for a couple over hours but can get the lamp to light This is on embedded mail, running 7.0 virtualized
  15. Cardine

    Hotel Phones with pre-programmed speeddial - how to find out what they are/were dialing

    We replaced a defective sx200 with a new 3300 MCD, at this point in the SMDR we only see the output or converted number, is there a way to see the actual speed call that it's dialing? Trying not to have to go into hundreds of rooms to reprogram all of the buttons. One of my techs thought it...
  16. Cardine

    Trapeze (juniper) MX-400 not booting

    BELOW IS A CAPTURE OF THE ERROR boot> boot Compact Flash load from boot0:MX070E01.04C. 12/11/30 16:00:53 RTC EEPROM CRC Mismatch: CALC_CRC 0x9de6 EEPROM_CRC 0x3a1b. Buffer not valid load_compact_flash: File <boot0:MX070E01.04C> is not a valid image for this platform. Compact Flash boot...
  17. Cardine

    Trapeze (juniper) MX-400 not booting

    had one brand new in the box, powered it up and I get the MGMT light blinking amber rapidly. Console in and the system can boot the image off the CF, when I type boot, I get a CRC error from the image and it won't load..... Anyone that knows this product better than I have any suggestions on...
  18. Cardine

    SIP ATA Teleworker shows offline

    Ok so I'm using a SPA112 ATA and it's configured per the docs, it works fine but occasionally it shows offline on the MBG, but it still is working. Reading through the Docs it talk about the GAP register and the Keep alives, I'm just not sure what to adjust to what. Any ideas?
  19. Cardine

    MICD ESM access keeps going down

    Anyone have any experience with the MICD platform. I keep getting this error - Nov 28 03:33:17 micd MiCSTenantStateChange[26136]: tenant0 javalayer has stopped running. ESM access is down And the only way to fix it is to reboot the instance....it is running the latest version of everything...
  20. Cardine

    Call Waiting Swap on Analog Phone

    So basically I have the call Waiting tone working fine, but it appears it breaks the forward to voicemail is you enable the call waiting Swap feature, has anyone encountered this? Scenario - analog user on a call, second call comes in and I hear the beep but the call never forwards to...

Part and Inventory Search

Back
Top