Search results for query: *

Hi, just wondering if anyone has got the Calendar function to work in CUEAC from CUPS/Exchange?

Ok, try using the call analyzer in servisability to see whats going on.

Your PT_SIP_TRUNK partition should be in a calling search space then on the phone/line put the CSS. For the route pattern just put 0. thats "zero dot" dont forget to select predot in the drop down on the same page, so when you dial 02000 eg it will strip the 0 and just send 2000, then where its...

Im new at CUCM too, but i think i can point you in the right direction. First setup a partition, call it PT_SIP_TRUNK or something. Then creat a Calling calling search space or add your new PT to one you have. Go to TRUNK and creat a SIP trunk using the PT and calling search space you...

BCM can only use SIP UDP.

On the BCM under Telephony-->Lines--> Active VoIP Lines, do you have any lines on window on the right? If so are they in a line pool and that pool assigned to a route and the pool assigned to a set? Sorry if you have done all this just want to tick all the boxes.

It will not effect your numbering, i have just tested it in my lab. Also it will not give you more TL.

Just to add: In the NRS: 1) BCM and SRG do not support TCP SIP Transport. TCP is default on the NRS while UDP is default on the BCM/SRG. Under Configuration, Gateway Endpoint, endpoint x (x = BCM or SRG endpoint in question), change the SIP Transport to UDP. Commit and save the change...

Under SIP settings make sure your "Outgoing Transport" is set to UDP. BCM does not support TCP SIP.

Yes you will need a CEC if you are going over 100 ext. The CEC daughter card carries four DSPs and delivers DSP processing power incremental to the three DSPs provided on the BFT. so from 100 to 300 ext you will need one CEC, fitted in the right hand module slot only.

Under Loops for the BRI change one of the ports from T to S. Then you need to give the S a Loop DN, go to All DN's and scroll down until you see DN that are assigned to ISDN make a note of this DN and go back to loops, under your S loop assign the ISDN DN to the loop DN. This should work for you.

Ok i have sorted this now. Looks like something has changed when i patched the srg50 for another issue. With SU8 you need to have "forward redirect OLI" ticked. srg's without SU8 you dont need this ticked.

SRG50 rls 1, fully patched. CS1k fully depep'd or so i have been told.

Yup, i have had the same problem. Also on BCM50 rls1/2 and 3. I now only schedule 1 patch at a time and works fine. I have not seen any fixes for this issue as yet.

Hi all, Another SRG50 question im afraid, the bane of my life these things, CS1K engineers always say it’s the srg not the cs1k lol. Problem is I have 5 srg50s and 1 is having a problem with incoming calls that have the number withheld. The call comes in on to the srg s BRI and it tries to...

Yeah i think your right about srg50 rls 1. Im upgrading all my sites to srg50 rls3 soon anyway, but it would be nice the tell the customer something..hehehe Our cs1k engineer has chked his site and says its the srgs.

Yup fully patched.

Hi, I have 5 srg50 rls 1 installed around the country and have been working fine for ages, three weeks ago they all start complaining of dead calls now and then. I have found out its only when a srg set calls a mobile or a landline number that is busy. The srg sets are no longer receiving bust...

Yes Vappl thanks, I have never had the problem before as I normally renumber the application DN's then all the routing numbers work. In the end the BCM bcm must have been using 28xx for something that was not visable so i just renumbered 28xx to 18xx and all is fine now. It would be nice if the...

I have inactive DN's starting with 29xx on the same bcm and im able to make a des code of 29A. I have 30 user bcm 200, DN's starting at 2700 - 3100. This sytem will connect to a cs1k in the US. On the BCM i need to route 20A, 21A, 22A, 23A, 24A, 25A, 26A, 28A, 29A, 3A, 4A, 5A, 6A, 7A up the SIP...