Search results for query: *

will a vcm4 fit an ipoffice 403 DT. it currently has 3.0.580 firmware the current vcm5 is showing signs of failing, it needs to be replaced. new vcm(5,10...) seem to be much harder to find than the vcm(evens).

thread940-1248609 ipo403 is now dead after power surge, thanks to the thread ref above was able to confirm the problem. kris, you say you where able to source a replacement chip after some time, could you give me the details of the supplier? thanks. mark

i think i have found the problem. 11 days ago i was going to update the firmware and admin software. i found a corruption of the admin installation; within the add/remove programs the admin software was not listed. i installed the original admin s/w as if it was a new installation. the...

its an vb front end, tapi interface and sql db. the tapi is not called directly but via a piece of software called ExceleTel TeleTools v3.6 this allows the vb program to make calls and popup on recieving a call at the extention logging the call details in the sqldb. it works well enough on...

hi disturbedone i give redoing the config from scratch on the old ipo403. i had uploaded the cfg once it went through the wizard and confirmed no issues. as for avaya's response i thought that might had been everyone else response too. but as i siad the firmware has been inplace for a long time...

via the dte port, i am getting a dab hand using that port unfortunly. yes the ipo403 was replaced with new boxed unit, still the same. least said about the s/w the better; as the manager could be reading this thread.;) the s/w has been working fine for the last year on that firmware version...

i have an ipo403 on 2.1.15, and has been that way for over a year without any problems until now. the avaya box reboots at different times of the day, and i have run out of possible tests to do. i have check with bt that the pri line is ok check the cable between the ipo403 and the nte...

forgot to describe it. it is yellow, rectangular with 6 pins on the underside which push fit into a socket on the board

i do not know about the 406 but the 403 has a time clock battery which plugs onto the main board. i found this out when i had to install a new vcm. maybe that is at fault not the mainboard

+++ START OF ALARM LOG DUMP +++ <TLB Data Error> CRIT RAISED addr=0086ca04 d=5 pc=ff5dbe60 ff5db644 ff5dbfc8 ff5e3460 ff7f06ac ff7eec24 <TLB Data Error> CRIT RAISED addr=0086ca04 d=5 pc=ff5dbe60 00000000 ff5dbfc8 ff5e3460 ff7f06ac ff7eec24 +++ END OF ALARM LOG DUMP +++ Within...

o well, thankyou for the info.

Thankyou all for the answers. now is there a way of having a DT30 60 feet away from the IPO403? could i use something like 2*10/100BaseT-100BaseFX bridging media converters? (IPO401, 1/2m cat5, media convertor, fibre, media convertor, 1/2m cat5, DT30) i have a good idea the answer will be no...

Thankyou all for the answers. now is there a way of having a DT30 60 feet away from the IPO403? could i use 2*10/100BaseT-100BaseFX bridging media converters? (IPO401, 1/2m cat5, media convertor, fibre, media convertor, 1/2m cat5, DT30) i have a good idea the answer will be no but i thought...

i have 4 remote users that use vpn over adsl. netgear dg834 at client end fvs328 at office multiple vpn tunnels each ip 4602 has a fixed ip a tftp service running on the voicemail server (for keeping the phones upto date) the voicemail server has routes added (route add 192....) to point to each...

What can the maximum distance between a IPO403 base unit and a IP400 DT30 expansion unit be ? i have looked through the ipo403 manual it tells me that i need a "Expansion interconnect cable" but it does not say what the maximum distance can be between the two units.

thanks sizbut, the files where not readonly attrib. i found a way around, i got one of the users to re-record the greeting and found out where the new wav file got created; because i have 2 folders greeting and greetings. i then restored the personal greeting into the same folder; this has done...

i have a problem with the voicemail pro, i have just moved the voicemail pro to a new server, all the messages, wavs and configuration files where restored to the new server. the messages and their status (new, old and saved) are correct; the mailbox names are correct BUT the personal greeting...

thankyou niclasr, spot on with softconsole.

dizzyphil my boss has the list of pswds, it is he who wants to be able to change the dnd state of an ext. i have tried through vmpro but with not success, if you could pm/post the solution that would be great thanks.

forgot to add the system details ipo403, DT30, 2030 phones, VMpro