Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. smetse

    Changing the forwarding destination when a user is off-network

    I read the whole thread again and I do not understand what you are trying to tell me, sorry. The Call Forwarding is NOT active on that extension before I try to do any forwarding changes... What am I missing which is so obvious to you?
  2. smetse

    Changing the forwarding destination when a user is off-network

    What do you mean by this: The system does not support forwarding to an off-network location. I can forward to off-network locations without any problem. I just cannot activate/deactivate forwarding to off-net using the telecommuter access...
  3. smetse

    Changing the forwarding destination when a user is off-network

    AvyaTier3, Here are the results after I tested what you suggested: 1. from the phone you want to forward, try call forward all code to the number you are trying to forward to. Call Forwarding Activation All: your_code, 9+1+xxxyyyzzzz PASS 2. from a different extension in the same switch...
  4. smetse

    Changing the forwarding destination when a user is off-network

    AvayaTier3, that's what I have: COVERAGE OF CALLS REDIRECTED OFF-NET (CCRON) Coverage Of Calls Redirected Off-Net Enabled? y Activate Answer Detection (Preserves SBA) On Final CCRON Cvg Point? y Ignore Network Answer Supervision? n Disable call classifier for CCRON over ISDN trunks? n Disable...
  5. smetse

    Changing the forwarding destination when a user is off-network

    Guys, thanks for your quick responses. All this is correct in my system: Extended Forwarding All (need y for the station) Extended Forwarding B/DA (need y for the station) Restrict Call Fwd-Off Net (need n for the station) The user's extension doesn't have console permissions, and I do use...
  6. smetse

    Changing the forwarding destination when a user is off-network

    Please help me with the Extended Call Forwarding. Everything works until I dial the last digit of the new 12-digit forward-to number (9+1+area code+ 7-digit number). Right after I dial the last digit, I get a busy signal. Below is what I found in the Avaya documentation. Am I missing any steps...
  7. smetse

    Octel 300 S.3

    doktor, As always you are quick and helpful! Thank you very much!
  8. smetse

    Octel 300 S.3

    Hello, I have 1208 mailboxes in the Octel 300 RELEASE S.3 There is no documentation left from a previous administrator. How do I find what mailboxes are used for company greetings/announcements? What commands should I use? Thank you.
  9. smetse

    Need help with call routing

    If you dial 800-xxx-xxxx or 978-xxx-2071 (this is a DID number, ext. 1222071), you will be connected to VDN 1222485, vector 137. Again, both numbers go to the same VDN/vector. After listening to the announcement 2632 and choosing between 6 options (vector 137), a caller is routed to different...
  10. smetse

    Need info on Mutare's Enabled VoiceMail (EVM) solution for Avaya

    Does anyone work (or know anything about) with Mutare EVM? What is good/bad about it? Any thoughts, concerns, suggestions?
  11. smetse

    Linux commands for S8500

    Mitch, Thank you very much! That's what I need.
  12. smetse

    Linux commands for S8500

    Is there a list of all Linux commands on the S8500 servers? How to find it? I am looking for commands to configure/change a modem to dial out a phone number. And the 'help' command doesn't help. Thanks.
  13. smetse

    DNIS question

    Thank you CL. That helps.
  14. smetse

    DNIS question

    Is there a way to see what incoming numbers (800 numbers for example) correspond to what DNIS numbers in the S8500 switch? Thanks.
  15. smetse

    911 question

    Trunk group 21 is the group in that location 2.
  16. smetse

    911 question

    CJH, Yes, there are different ARS tables for each location. The ARS table for that location looks like this: display ars analysis location 2 9 ARS DIGIT ANALYSIS TABLE Location: 2 Dialed Total Route Call Node ANI String Min Max Pattern Type Num...
  17. smetse

    911 question

    I have three S8500 switches in different locations connected together (ESS). When 911 is dialed from a remote location, it shows on the main switch and the local (main switch location) police is notified. How to configure the switches so the local police to each switch is notified in case of 911...
  18. smetse

    Using Do Not Call Registry

    Does anybody know if there is a way to upload a range of phone numbers into the NATIONAL DO NOT CALL REGISTRY? Thanks.
  19. smetse

    how to block phone numbers?

    Thank you, I got it now. Here is what I have in system-parameters customer-options: Maximum XMOBILE Stations: 0 0 If I need to block say 10 incoming numbers, do I need to create an xmobile station (when I have licenses) for each number? Or I can use the same xmobile station for...
  20. smetse

    how to block phone numbers?

    phoneguy55, Your instructions are not clear for me. What commands do I have to use? What is the relationship between xmobile and EC500?

Part and Inventory Search

Back
Top