Search results for query: *

OK, After further testing, The Carrier has not changed anything.. I can dial 847 numbers now but not 630, which are flagged as locl. I get the invalid number format. Any Idea's?

OK, Here is what I did. Please verify this is correct. Created DMI 2. changed CTPY=NXX Created RLI 7. Set to route 0 NPA- changed 1630 to RLI 7 NXX- Changed 847 to RLI 7 For some reason I can not add 1847 to the NPA. This is the area code they are in.. Is this defined elsewere? When I whatch...

Should they be in NXX or NPA? I show 1630 in NPA and 847 in NXX. Or just make a new route for these and assign the DMI?

As of yesterday Verizon added 1+ dialing in our area.. After their change I can no longer dial 847 and 630 (local) calls using 7 or 10 digits. After speaking with TAC, they said the calls are going out as national ISDN and should be flagged "local or Unknown". How do you define the type of call...

Is there an easy way to collect call counts to a voicemai dn (acd) besides CDR? I would need to see all traffic that hits the pilot number- answered or abandonded internal and external. I need to do this for 1 week and was looking for the best way. Thanks, Don

I do not recall seing an on/off switch on the card or daughter board. Where might it be? Thanks, Don

Here is some config an at the end msdl commands.. Thanks again.. Don .stat dch 2 DCH 002 : DSBL RST AUTO DES : dch ADAN new dch 2 CTYP msdl CDNO 0 CDNO 1 PORT 1 DES dch2 USR pri IFC d100 DCHL 0 DCHL 2 PRI 2 OTBF DRAT RLS RCAP MBGA TIMR LAPD stat msdl MSDL 2: MAN...

I will send this in a bit.. I need to get the txtr off of the laptop Thanks guys..

OK.. So I tried it.. No Go. When I go to turn up the dch it does not come up. If I stat msdl I get it is man dis. If I try to enl/dis msdl 2 I get an sch- stating the msdl card does not exist is that location. Did I do something incorrect? Could somebody be specific on how to set up the msdl for...

Thanks.. Yes this is the first PRI in the switch. Currently there is 1 T-1 in the switch but it is being converted to the PRI. Anything change?

Is that on the PRI card? Is there a way to find out if it is there in software or is it always there? How would I find the device number? or does it just need to be diff. than any others in the system?

Thanks John.. U R DA BEST... I hope it goes that well.. SW= Option 11 with a NTRB21AB card.. Still the same, right? As I read it the card has a built d-channel or did I read it wrong. Don

I am changing from a fraction T-1 to a PRI circuit. Colud somebody refresh my mem on the ld's used and anything that may be an issue. Thanks, Don

John.. Thanks I will give it a try, although I think I may have already, But try again I will. Kprintz, Thank you for the sugestion. The main goal is to get them to a person or directly into a VM box (Medical Office). They do not like the ran idea but it may be the least expensive. GHTrout...

I have a Meridian Mail system on an Opt 11c and the problem is not enough mail ports. Is there any way to send calls to a DN when all ports are busy or NA? If someone calls in currently they just ring na. Any sugestions? Thanks, dOn

Thanks John, the number FNA to the receptionist. But if nobody answers then it is gone. I am trying to determin Who is not answering. is there anyway to pull this info from the system without constantly monitoring it? I am about 70 mile from the place and do not want to keep a remote session...

In Ld 20.. Stat. This will not show trunks but will show stats for dig and analog sets Hope this helps.

I have 3 800 numbers ringing to 3 seperate group via MCR keys on all phones. People are reporting RNA. I found no problem. Is there a way to continually monitor calls comming in and where/what their current status is? Call Flow: 800#-DN7XXX-(B/NA)-2xxx. Is there a way to monitor and pull...

I believe 4.. I am still waitng for full telco details as I did not order.. I just Doo.. What would change?

We just got a new group of DID numbers 9400-9420. Our current block is 2800-2899. We use "9" do access an outgoing route. How do I route the New 94xx numbers to say a dn 44xx. Is this possible with the lead number being the access code? Thank you in advance. Don