Search results for query: *

you need to use the "set port" commands to enable and configure the physical ports. PG

Check that you have the new range in public or private unknown. PG

Do "change system-parameters coverage-forwarding". On page 2 check that "Coverage of Calls Redirected Off-Net Enabled?" is set to y. PG

You need to have the little fire cracker thingy installed between the CSU and the network: 700406101 1 DS1 LOOPBACK JACK 700A RHS PG

XL versus Standard Differences: Trunks from 8,000 to 12,000 CLAN Boards from 64 to 106 EC500 Enhanced CLID Support from 54,000 to 108,000 off-PBX station-mappings Tone Detectors: from 1,200 to 8,000 Announcements: from 3,000 to 9,000 VAL boards: from 10 to 128 Attendants & attendant groups...

From the main menu try pressing 5 for personal options and then 5 for record name. PG

If it's coming up on VLAN 0, I would suspect that the TESTVLAN timer ran out before it got an address and so it is using that value. Do a CLEAR# on the phone and try it again. PG

Doubt 1: You only need teh VLAN info in the desktop scope. L2Q=1,L2VLAN=200 Doubt 2: You can have the L2VLAN=200 in the desktop scope because the desk tops won't be looking at option 176 or 224 and probably don't have the ability to tag anyway. Doubt 3: 1= L2Q on, 0=L2q auto The config you...

You need to add the DHCP options, 176 and 242 to your desktop scope as well. You only need the L2Q=0 and L2QVLAN=200 strings, that way the phones will know they are on the wrong VLAN and reboot on VLAN 200. I always use L2Q=1, but I don't know that what you have won't work. PG

I don't know the pinout of the cable or what's connected other then 1,2,4 and 5, but 700395445 is the comcode for the 50 ft cable The firecracker is a loopback device. The CSU 120 and the MM710 have no internal loopback capacity. PG

700395445 1 120A CSU CABLE 50FT RHS A1 $30.00 PG

Have you checked that the Node number in Dial Paramenters and in Switch Link are the same? PG

Problem: Unable to load new license with Tenant Partitioning turned off. Platform: S8300/G450 CM5.2 Background: Single site S8300 with G450. We want to use Attendant Backup, which requires that tenant partitioning not be enabled. The current license has TN enabled, I have created a new license...

Controlled Slip Seconds. The number of seconds (maximum of 255)with one or more controlled slips (a replication or deletion of a DS1 frame by the receiver).

I have a customer with S8500 CM5. We are doing weekly backups to flash and I have selected save 9 data sets of data. The problem is it is only saving the last 4. This is a fairly small system so I can't imagine that the card is full. Anybody know what I have done wrong? Thanks PG

I would suspect a routing issue. I would put a static route in the server to point to your new IPSI using the CNA interface. PG

You can only use Far-End mute on calls that come in on trunks, not on stations on the switch. You should be able to drop them though. PG

You need to put in the correct IP route.

Your problem is that you are saying in public unknow that the total length of the CPN is 10 digits and the first 8 are 03391789. So the switch only append the last 2 digits of your extention. You need to change your CPN length to 12 to send all the digits 033917896870. You also need to make sure...

Your configuration is perfectly valid. If you take a look at Communication Manager Software & Firmware Compatibility Matrix , you will find that Main server at CM3 and ESS at CM4 is compatible. The times I have had issues with file sync is when I had the ESS pointing to the wrong interface on...