Search results for query: *

I want to program *1 to route to an external number as a "speed dial" for a frquently used number. Can someone point me in the right direction for the programming please?

To save on time I wondered if anyone had found anything, likely 3rd party, ways of an automated process that could reset a users unity pin and email it to them so it could be a self service process? Also perhaps for user phone logins too. Thanks.

Panic over. I have managed to make them PLDN's wth a GPHT to the number required!

Currently *1 is used as follows....... DN *1 TYPE FFC FEAT AUTH Can't 100% remember what that one is, and pretty sure no one uses it. And yes I want them to dial another number when a users keys in *1 or *4357 I am assuming I couldn't make *1 and *4357 PLDN's?

I have had a request to create 2 speed dials for all users in the office with the keys pressed *1 and *4357 Can anyone advise how this could be done please? Thanks.

Thanks, I am aware of the analogue capability with a analogue gateway but should of explained I am really looking for an IP conference phone but a cheaper alternative to the Cisco range.

Hi, I just wondered if anyone had found/tried any non Cisco conference phones that were perhaps cheaper to purchase than the likes of the 7937 ? Thanks. Tom.

Hi, I was wondering if anyone knew of a way to extract data from the meridian so it is suitable for a .csv or similar? I am looking to get all the extensions listed with perhaps the names also against that? Thanks. Tom.

Hi, Is there a way to restrict by DN/TN the phones that do get MOH if it is branded for a certain department? Thanks. Tom.

Hmmmm still no luck :-( Still just getting the NU tone when I try and set the forward to 07595 xxx xxx. Any other ideas anyone? This is really beating me this one! TYPE RDR_DATA CUST 00 OPT CFF CFRA DSTD PVCA CWRD MCI

Thanks, I do indeed have CFO. To change it I assume, ld 15 chg rdr opt cff ? Thanks. Tom. REQ: prt TYPE: rdr TYPE RDR_DATA CUST 0 TYPE RDR_DATA CUST 00 OPT CFO CFRA DSTD PVCA CWRD MCI

Here is a trac of a phone successfully calling the number .TRAC 0 7413 ACTIVE TN 016 0 11 11 ORIG TN 016 0 11 11 KEY 0 SCR MARP CUST 0 DN 7413 TYPE 3904 TERM TN 8 28 IDA RMBR 91 87 OUTGOING TRUNK CALL DIAL DN 907595xxxxxx MAIN_PM DIAL AUX_PM DPNSS_S_DIGS TALKSLOT ORIG...

OK it seems that there is a bit more to this. Now I have checked everything myself with the user it is just they cannot call forward their phone to the number. You can dial the number fine from the handset. This is also the case when trying to to it on my phone wiht NCOS 7. Here is a prt of th...

No there isnt. SPN 06 FLEN 11 ITOH NO CLTP NONE RLI 30 SDRR NONE ITEI NONE SPN 077 FLEN 8 ITOH NO CLTP NONE RLI 30 SDRR NONE ITEI NONE SPN 078 FLEN 8 ITOH NO CLTP NONE RLI 30 SDRR NONE ITEI NONE SPN 079 FLEN 8 ITOH NO CLTP NONE RLI 30 SDRR NONE ITEI NONE SPN 08 FLEN 11 ITOH NO CLTP...

I have checked for any SPN and there is no SPN. Any further advice on what to check would be greatly apprichated!

Hi, I have an issue where I cannot dial mobile/cell phone range of numbers 07595 xxxxxx on phones with NCOS 6. They work fine when dialling from a phone with NCOS 7. But I cannot see anything in NCOS 6 to block it? I have a hunch there is some other programming in the PBX I need to look at...

REQ: PRT TYPE: TNB TN 4 0 13 8 DATE PAGE DES DES TECH TN 004 0 13 08 TYPE 3904 CDEN 8D CTYP XDLC CUST 0 FDN 7878 TGAR 2 LDN NO NCOS 7 SGRP 0 RNPG 99 SCI 0 SSU LNRS 16 XLST 0 SCPW SFLT NO CAC_MFC 0 CLS TLD FBA WTA LPR PUA MTD FNA HTA TDD HFA GRLD CRPD STSD MWA LMPN RMMD SMWD AAD...

865 XXXXX AND 861 XXXX both go to the same cisco voip gateway. 861 plus the 4 digit extension works perfect and has done for years. There is no dmi on the route for this e.g. DMI 0. 865 requires a 5 digit extension after it, the FLEN in the DSC accounts for this (flen 8), it then uses the same...

Extension range at other site is 50000-59999

The calls route and fail when just calling also, not just when trying to forward.