Search results for query: *

Excellent! Tek-Tips rocks!!!!

I have recently printed out a traffic report for my trunk and route useage but cannot decipher what all the numbers refer to. Can someone help?

Do you have an external tape drive for your mail system? If so you should shut it down and INI the pbx. While the PBX recovers from INI power on the external tape drive and the links should establish. I have had this happen with power outages where the pbx recovers first, then the tape drive...

You may want to check your pinouts. I made my own cable for our 61c using the following: DB25F - DB9F 2 - 2 3 - 6 4 - 4 5 - 9 6 - 8 7 - 3 8 - 1 20 - 7

I believe I am running Rls 11.19. Does this help?

I think my baby is prior to that. I have newer Opt11's with the admin and tools levels, but this one doesn't ask for a user id, just the password. Is there a way around it? Right now I am scurrying through paperwork trying to find the keycodes or the original install tape...

luv2ski - no error msgs on screen, pbx rls 23.35, still looking for mail release

You need to set up the modem using the following: 1. Turn off power to modem and set all dipswitches to the down position. 2. Connect to your laptop via DB/9 - DB/25 cable and power on. 3. Setup a new connection via Hyperterminal and set the baud rate at the speed you want the PBX connection to...

First of all a big Thank You to all who have responded. Superior - Just tried "AX -space- 1-10" and "AX1-10" When I type a space between AX and the number it immediately attempts to switch to mail. I never get to type in the number. With no space I get an error code...

I have XP home and my outlook doesn't have spell check available. The icon is there, I just can't select it. Is there a setup tool I am missing? Or a format error? Any help is appreciated.

Arch - I have rebooted. I also tryed changing ports on the Mail card, changing out VT's, changing and rebuilding TTY's, swapping cables for TTY's, courtesy down mail, INI PBX, and Reboot PBX. Maybe I should reseat card? Perry - When I hit Print Screen the printer prints out the mail menu...

No go on the CTRL-R. Anything else? CTRL-] still backs me out of mail, and AX definitely gets us there. After I type AX I hit print screen and the mail menu prints out. I just can't see it! Crazy stuff.....

Hi, I have had an issue with my VT for a while now and was hoping for some help. I can log into my Opt 11 no problem, but when I type AX to reach Meridian Mail, the screen goes blank. I access mail, just have no visual response. It used to work with a modem tty, but has now migrated to it...

The pad values you have are Nortel's defaults for Pad Category 1 DTI/PRI values. According to the NTP's, the pad prompts above are as follows: PRI = 1.5 Mb/s PRI/DTI trunk PRI2 = 2.0 Mb/s PRI/DTI trunk The defaults for those are Rx=0 and Tx=0, just like you have. Hope this helps!

On the Meridian line you need a music route and trunk. Then you need to allow music on your voice trunk routes. Not sure if the Norstar is the same as I have minimal time on them. Check your software feature guides if you have them. Good luck!

Thought about doing that earlier, that's probably one of my next steps. I just don't want to hide the issue by increasing my thresholds. Only problem is I haven't shown an error on my 61C at all when this happens. I did an LCNT and it shows all good. I'm Easter-egging now and swapped out...

Quick history: I have two T1 loops and have recently began having issues with one. Loop will remain enbl but all channels go dsbl for no apparent reason. Had telco pull up history on their side and show no problems. Monitored with TBerd on our end and saw minor BPV's, but nothing that would...