Search results for query: *

I have a full T-1 connection between sites. Both sites are running VoIP. The routers I am dropping in are 1721 with T1 WIC cards. What commands would I use to give VoIP priority with the bandwidth that I have. Thank you!!!!!!

I need to add a statement to my access-list to only allow email from the following outside mail server. 12.12.x.x My current access-list is as follows: access-list 101 permit tcp any any eq www access-list 101 permit tcp any any eq smtp access-list 101 permit tcp any any eq pop3 access-list 101...

Question - What are the proper commands for a t1 to the Internet? I know the commands for a 256 are as follows, but what about a full t1 to the web? interface Serial0 bandwidth 256 service-module t1 timeslots 1-4 Thank you very much!!!

I need to use my router as a DHCP server. I need the following ip scheme used... IP address pool - 192.168.1.3 - 192.168.1.50 Default Gateway - 192.168.1.1 DNS - 192.168.x.x Thank you for any help you may have!!!!

I am needing to setup a Frame 256k point-to-point. I know how to setup the routers for a full T1, but what is the commands that must be entered for a 256k circuit? Also, what interface do these need to be configured on? Thank you.....

I need to deny a group of internal IP's Internet access. Please assist. Let's just say that I need to deny the range of 192.168.0.50 - 192.168.0.100 for Internet access. What is the proper ACL and Access-Group to set this up? Thank you....

I am very familiar with the Netgear and Linksys DSL routers, but I have a client that wants a Cisco DSL router. Any idea if Cisco makes software to automate this process?

Is there some product out there which is like ConfigMaker that will assist in the planning of a config for a DSL line? Any help would be appreciated. Thank you Secureinc

Here is the situation......I need to be able to forward all traffic on ports 110, 32000, 32001 to a internal mail server's IP address. (Let's just say 192.168.10.10)I do not want to have to use on of my available public IP addresses for this configuration. Does anyone have any ideas? Thank you

You could try adding a "ip-helper" address statement and you could also add the following in global config mode: ip forward-protocol udp netbios-ss I hope this helps

Cisco ConfigMaker also has a great utility for calculating subnets

I may be able to point you in the right direction. First of all is the line going to be point-to-point or Frame Relay? Ask your ISP for the following information and then maybe I can send you a basic config. What is the LMI Type? What is the DLCI # (if Frame Relay)? What is the IP address...

I have a Cisco 804 IDSL router. I am familiar with Cisco CLI but not with DSL configs. Does Cisco make anything like ConfigMaker that will help with DSL configs? If not can anyone supply me some cool links to some sample configs? I have looked at Cisco's website, but I'm not to sure what I'm...

I have a Cisco 1721 and I need to see if certain pings are reaching my e0 and s0 interface. How do I do this? This router is not running nat.... Thank you

Below is the config on my router. What I need to do is to nat 192.168.10.200 to a public ip address of 4.67.21.xx. How would I do that? Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption...

This is my routers current config. I am trying to telnet to the router from the outside and it it not allowing any connections. How can I set this to allow telnet access from the outside? Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service...

I need to open up MS NetMeeting on my PIX firewall. I have heard that NetMeeting is a huge security risk, but I still need this done. Below is my ACL... access-list outside permit icmp any any access-list outside permit tcp any host 66.35.160.x eq www access-list outside permit tcp any host...

Could someone please explain this alittle more indepth to me. I know that for a T-1 you would use "service-module t1 timeslots 1-24", but what about for a 256K Frame-Relay connection to the Internet? How does the bandwidth rate relate to the number of timeslots? Thanks....

I have a Cisco 1605 that is going to handle my network Internet connection. The s0 ip address is 4.25.163.x. The e0 ip address is 192.168.10.2. I do not have any type of firewall to do the nat. So, what would the proper nat statement be to allow my client pcs to access the Internet?

What type of connection are you using the router for? What port numbers do you need to use for your VPN?