Search results for query: *

OK. I think I've got it. LDID with RLI in NPA programming for local DID trunks and DID for distant DID trunks on-net including route programming at the RDB: LD 16 Type TIE CNVT YES DDMI 5 (references DMI 5)

I have a Meridian 1 Opt 11C ver 2111 rls 25.30+ with 2 TMDI PRI spans. One supports tielines and the other is CO/DID trunks. I would like to reroute DID calls to the PBX at the other end of the tieline over the tielines first, then the CO/DID trunks. I would also like to redirect callers who...

No, Curly. I searched Yahoo for "Flashtalk Programming record" to no avail. I have it now and thanks for the tip!! Dale

Thanks to this forum I have been able to "stumble" my way through setting up CCR on Flashtalk. My setup and operations guide makes reference to a StarTalk Flash Programming Record. I do not have one but thought it may help with future programming. Does anyone know where I can get one? (Flashtalk...

Thanks Don. It does work when I wire up a single line off of the Meridian 1. I suppose I will have to break out the oscilloscope and compare ringing signals between the two.

TYPE RDB CUST 00 DMOD ROUT 2 DES COT TKTP COT PRIV YES SAT NO RCLS EXT DTRK NO ISDN NO PTYP ACO AUTO NO ICOG IAO RANX NO TRMB YES STEP CPP NO TARG CLEN 1 BILN NO OABS TIMR ICF 512 OGF 512 EOD 128 DSI 34944 NRD 10112 DDL 70 ODT 256 RGV 640 FLH 510...

TN 020 0 00 03 TYPE COT CDEN 8D CUST 0 XTRK XUT TIMP 600 BIMP 3COM TRK ANLG NCOS 1 RTMB 2 4 PRDN 5013 CMF NO SIGL LOP SUPN YES STYP BST AST NO IAPG 0 CLS UNR DTN CND WTA LPR APN THFD P10 TRC LOL TKID DATE 8 APR 2009 TN 020 0 00 04 TYPE COT CDEN 8D CUST 0 XTRK XUT TIMP 600 BIMP...

...and I am trying to get it to ring on a multiline set if that makes a difference. (I do have 1FB's working this way on the Universal trunk card in question)

Correction: The Meridian 1 is an option 11C.

I am extending a phone number off of an SL-100 (distinctive ringing off) across an Adit 600 FXO FXS circuit into an NT8D14BB (rls 06) Universal trunk card on a Meridian 1 (Rls 24.24+). I am able to seize the line outgoing from the M1 but cannot get the trunk card to ring through to the line on...

That did it. Thanks NorstarWiz1

Upon further review I have noticed that the inside message was returned due to an extended absence greeting...

I have a user on a StarTalk C2 that has a mailbox that will not accept outside caller's messages. I cannot access the mailbox remotely (using ** login) but can send a message from an onsite mailbox. I do not know how this restriction came into play and therefore do not know how to fix it other...

I have an Octel 350 with Aria 3.00.09-1 software. The system has 4 file cards. If I number them 1 to 4 (left to right) I see that 2 and 4 are the active (ACT) cards and 1 and 3 are standby (SBY). I suspect that the system may have switched CPU's. CPU switchover is set to Normal: N Abnormal: Y...

Thanks for the replies. Pretranslation did it.

I am trying to set up a modem line that will automatically seize an outside line (user does not have to dial 9). I had this set up years ago on an SL-1 but don't remember how I did it. I am currently trying to set this up on a Meridian 1 Option 11C 1121 rls 23.55. (I have tried CLS MNL with...

...FastRAD that no longer works. I have replaced the FastRAD with a known working FastRAD but still get "Inactive Feature" when I attempt to program it using F9**. I have not tried a cold reboot on the KSU and was wondering if there is another way to reset the RAD. Thanks in advance. Dale in...

I've purchased a replacement CallPilot and as a test I have swapped out the power supply (the new CallPilot had the new 2 prong power supply) and the system came right up. So, if I can find another power supply, I will have a working spare. Do you know where I might find one? Dale

I have an 8X24 DR4 rel 01 and have programmed 2 ATA's as hotlines dialing another office. I have set them up to access line pool A. One of them works properly and the other will occasionally terminate on an intercom in the same office (manager's phone of course). I have not been able to...

Thanks Rik. Would the replacement power supply be external? I assume the 3 prong supply your are referencing is the A/C plug and not the DC input plug to the CallPilot. Dale