Search results for query: *

I have seen in other posts that you login as craft and then use sroot is that correct? Sorry but I am a newbie to linux commands Cais

Hi mrjedi, I guess i needed to be logged in as sroot in order for the 'netconfig' to bring up a new screen. Do I have to be in any particular directory to run 'netconfig' Thanks... Cais

Thanks Guys, I will try that. I wish Avaya had put the sroot login info in the document. What command can I use within Linux to see if netConfig changed the ip address of eth1. Thanks, Cais

Hi mrjedi, No...I have been following the Avaya document. I just putty to 192.11.13.6 services port on SAMP and logon as craft & craft01. I am missing something? Thank you. Cais

Hi All, I am trying to change the ip address of ETH1 on an AES server. I am connected via putty to 192.11.13.6 on services port. I have tried netConfig eth1 up static 192.168.1.1 255.255.255.1 192.168.1.254 but I think this is wrong. Does anyone know the correct command? I also came across a...

Hi All, Can an ESS server running 3.1.4 run off main servers with cm 3.1.2 or does the main servers need to be at a higher release than that of the ESS servers? Thanks, C

hI Guys, I am trying to figure out how to route incoming calls into HQ to remote G650. I do not want the call to go over the Network but would like calls to go over the DCS trunk between HQ and remote G650. I believe IGAR can be used but not sure about the LDN ext for each site as the same ext...

Hi all, I have a PN with 5 G650s A-E I dont need carrier E. I changed cabinet 1 and removed G650. No translations were associated with this gateway. Moved the termination adapter to D. The problem is that the whole PN did not come back up. Eventually I put the G650 E back and everything...

Hi Petran, Thanks for the info. I will let you know the outcome. Regards, Cais

Hi Petran, Thanks for that. I can see that we are getting 4 ES (errored seconds) on the trunk every 15 minutes. How many errored seconds are tolerable? if any I issued the command ' list measurement DS1 log 03c14' Thanks again, Cais

Hi petran, Thanks for that. I have it set as follows: MG-001-1(configure)# set sync interface primary v4 MG-001-1(configure)# set sync source primary Would errors on this trunk cause voice quality issues from LSP site to main location? Cais

Hi Guys, We have a number of LSPs and ESS throughout our network with duplicated S8720s. At the central location we use our carrier BT as the primary sync source. My question is what should the DS1s in LSPs be set to? I have them using our carrier BT as primary sync source. Should this be set...

Hi Guys, Does anyone know where I can find out the Ethernet port layout on an S8720. There are 7 ethernet ports and I am trying to find a document that labels each port. Thanks in advance, Cais

Hi Nath42, Thanks for your reply..... OK I need to find out why this was left out and need to get documentation on AES server. Thanks again, Cais

Hi Avayafreakje, Thanks for your reply. So you would programme the CLAN to point to the CTI server...have I got that right? Are there any sample documents on programming the Clan to do this? Thanks, Cais

Hi all, We are upgrading from release 9 to CM 3.1.2 My question is, what do I use to replace the Mapd board? Do I need an AES? or will a CLAN work ?? We have purchased ASAI core and plus lisence. Thanks in advance, Cais

Hi BHodgins, Thanks for your reply. The router engineer has asked me to turn on enbloc as this will wait for all digits and then send them out. He claims that its set up using overlap. He can tell this by running debugs on the cisco. But I have enbloc set for both incoming and outgoing. Any...

Hi Guys, I have an Avaya G3Si with a DS1 connected to a E1 port on a cisco router. When I dial the trunk access code and dial a number, it takes longer for the call to connect compared to going out over the ISDN. Am I missing some programming on the G3si to speed this up? Thanks in advance, Cais

Hi mrjedi, Thanks for that. That worked. Great. Regards, Cais

Hi Guys, I am trying to install Ia770 from the CM3.0.1 CD but as soon as the option appears on my screen it just skips the option and continues installing Call Manager? It comes up for 2 seconds and then gone?? I am using a USB cd-rom. Anyone come across this. Thanks. Cais