Search results for query: *

I did notice that the LED labeled A for the TLAN was on steady where as the one on the old card is blinking.

This is a CS1000B in a MG1000E cabinet, if that is what you are asking. The software on the CS, SS and VGMC are all 4.5

This is a second MC32S card that I am adding. The original card is F000 all the time. The Signaling Server as been in service for about 5 years or more. Therefore the IP address on the Sig Server is not in conflict. I am leaning to the port on the switch not being set up correctly.

Looking for some help. I have a VGMC card that keeps toggling back and forth from F000 to M000. As anyone experenced this and are the able to help me resolve this. Not sure is this maybe a network issue or not. Thanks

New info. I have found that it is only the digital sets having issues. analog lines are fine.

Hey folks I am having an issue with a CS1000E site. Below is what is happening. Both sets are NCOS 6 Start with the WORKING IP SET 1120E set calls Norway over SIP. Calling 75562869 Call is getting a Ring No Answer Now the NO WORKING TDM 3903 set calls Norway over SIP. Calling 75562869...

Hi I had this situation on the weekend and all is up now but wondering what the root cause might be. Customer has 3 Analog cards in slot 6, 7, and 8 in Loop 0 shelf 1. There was no dial tone. Card in the other shelve worked fine. The issue started as an analog line was not working. I disable...

Does anyone know if it is possible to to Play an announcement from the CallPilot of a PA system? A customer wants to, In the case of an emergency be able to play a pre-recorded message over the PA system from the CallPilot. They said that they were able to do this on their old Octel system.

Thanks Reusser The MGC firmwire is up to date. Also to my last comment about the audit conducted, the testing did not mention anything about the PRIs having any issues, therefore I beleive that it worked before.

I know we did some audit testing before this system went in to production back in december 2008. I don't remember us having these issues back then. I will go back and check the results.

I did do a FDL and still the same result.Before pulling the active CS I connected to the standby and the DCH does establish. ?????????

Hey John, will we not have the same issue even if they are split? I mean the Call Server is down and when the other core comes up will the D channels still not act stupid?

Have and issue with a CS1000E HA 5.0. Here is the situation. Call Server 0 is in building A and Call Server 1 in building B. The ISDN setup it two physical T1 as one PRI with a primary D and backup D. The T1 for building A is in l s c = 4 0 3 Loop 78 DCH 14 Primary with its own primary clock...

Thanks, I was not tlooking in the right place.

Does anyone have a copy of the 1120 C60 firmware? Thanks

Hi Mike Thanks, that is what I found out as well. gwebster You are right, I quoted the wrong bin name. I mixed up the letters. I was working on i2002 and i2004 as well. Bite mixed up there. Thanks guys

I am having issues trying to upload the bin file toe the sig server. I select the bin file and press the button to start the upload and the hour glass spins and then stops. I checked to see if the file was uploaded and it does not show in the list. I uploaded a couple of other firmware bin file...

Would anyone hare a solution for the following issue. I have a customer with a CallPilot 5.0 1005r HA system. I recently changed the IP addresses for the CLAN, ELAN and managed IPs. This seemed to go fine, but when I try to bring the main Callpilot server back on line it gets down to the CP...

I have a customer with the exact same issue. Anyone else seen this. Thanks

Here is what I got off Nortel site. I have 16 IP Users and No Basic IP Users. Solution Detail srpt214 Unable to add MGC to system after upgrade to 5.0w -------------------------------------------------------------------------------- Problem Description SRPT077 IPMG[8 0]: Loadware version...