Search results for query: *

You are facing this problem within single cabinet or when you transfer the call to second cabinet. Do check out your VGWs status while facing this problem.

change DIDN to YES (LD 15) if you want your DN to be passed as well after HLCL Prefix, otherwise only HLCL entry will be passed... My Experience...

Just hit the spot. In CLS of Trunk TN, it was DTN (Digitone). I just changed it to DIP and things started working. I don't know why nobody though about that. Problem resolved. Thanks for your kind anticipation.

I have split 30 channels into 20 + 10. 20 are in one route and 10 are on other. This issue is happening on 10 separate channel. If IFC was the issue, other 20 channels must exhibit the same problem, what you say?

I have tried to loop back my Analog Ext as well to Trunk Card. Same thing. Analog set directly to trunk works perfect, and its on DTMF.

Doc, I have not a single post with 40 replies, trust me. I have tried Nortel documents, tried to read the old captures, tried reversing polarity, card slot, TN. I still doubt on my configuration and that is why I am asking you guys. There are some issues and thats why I can't call Vendor right...

Tried another XUT on 2 different slots. Nothing worked. Getting the tone, but not dialing. Any guidance plz?

...#31 - NORMAL UNSPECIFIED DCH 18 UIPE_IMSG CC_RELEASE_IND REF 000030EA CH 18 1 TOD 16:09:04 CK 00D1A1FA CAUSE: #31 - NORMAL UNSPECIFIED DCH 18 UIPE_OMSG CC_RELEASE_RESP REF 0000B0EA CH 18 1 TOD 16:09:04 CK 00D1A1FA ********************************************************** Please guide.

ISMs for Mobilx separately? or we can use ISMs for IP Phones or Digital Phones for the purpose. Secondly, can you please point the details out for Rls 5.5j NTP?

So, is it possible to install a 2050 Softphone, forward all of its calls to my cell phone and use my cell phone as if it is a DN (at least caller will not be having any clue of all this), Right?

I tried crossconnecting a simple analog set directly to the MDF. It gives the dialtone and dials the number as well. Tried changing TN as well, nothing happened. Can it be the card fault? Any other check remaining?

I am asking if it is possible in CS1000E. RIGHT forum :)

I am not sure. Plz tell me how to go ahead with both options? I mean what will be the possible solutions if the trunks is loop start or ground start?

I once installed a BCM 400 with a softphone having Keep Alive option. What it used to do is that it just kept my Softphone working even if my notebook was powered off. I used to transfer all my calls from that virtually alive softphone to my cell phone. Just want to confirm if this option is...

...CLS UNR DTN CND ECD WTA LPR APN THFD CLID SPCD P10 NTC TKID AACR NO DATE 10 MAY 2010 LD 21: REQ: prt TYPE: rdb CUST 0 ROUT 11* ROUT 100 TYPE RDB CUST 00 ROUT 100 DES TRUNK TKTP COT NPID_TBL_NUM 0 PRIV NO RPA NO SAT NO RCLS EXT VTRK NO NODE DTRK NO...

Any solution plz? I am stuck...

I have 4 E1s, all configured but 3 running. Please be a little specific about what to check in LD 60? Thanks

I guess at the moment I have configured Pilot DN setting. I have DNs 17, 137 and 147. Setting is: 17: Hunt 137 137: Hunt 147 147: Hunt 17 This works fine if 1st is busy, second rings, second busy third rings so on. What I want is that when user dials 17, first set (17) should be rung. Second...

I was asked by a client about this. Since I am relatively new in Nortel, I was unable to answer precisely. Is it possible to create a Hunt group with Cyclic call (like calls in sequence 1-2-3-4-1-2-3-4.... on 4 DNs)? How to achieve it in simplest way, not involving any ACD thing?

lOl @ Telnet as a best GUI. CLI is themost flexible way of gripping ANY system. I used to program Alcatel OXE in GUI mode and trust me, it was enough to make me out of mind.