Search results for query: *

AvayaRedTech, I performed the 'nvram init' and reconfigured the IP. I can access the CLI of the G450 but getting hung up on SNMP3 when accessing the web site. I havent done anything with the S8300D. Although I can access it using the admin account, I can only access BASH and the web site. I...

So I did get lucky with Admin\Admin01. I was able to login to the CM and found the error - there is no license. I get this message roughly 30 minutes post boot. It seems like it cant find the license and then gives up. This switch was part of a survivable failover that no longer exists. I...

So I dont have any passwords for the S8300D. The other company outsourced the support and the guy that use to support the system quit. I know I have to call Avaya but is it worth it if the card is bad? Or should I replace the S8300D? Is installing similar to the CS1000 where the system board...

You are correct. That's exactly what it says. I was thinking it would have said it after the S8300 but that's what I get for thinking.

It is a S8300. No letters after it.

Hello, I received an Avaya G450 with a S8300 card from a sister business. I was hoping all I had to do was plug it in. Wrong. I have a solid red light on the S8300 and show faults states "Primary Controller Not Found". I can connect to the Services port on the S8300 and ping it. Does the...

Hello, I have a Siemens Hipath 4000, software v.6 that I'm looking to integrate with a Cisco ISR 4331. We were planning on running an E1 from the Siemens to the ISR and route calls as we switch over to Cisco UCM. Does anyone have experience with this type of migration? If so, is it possible...

Awesome. Can you tell me what software I need to download? I dont know how to read the version number and match it up to what's on the Avaya site.

Hi Firebird. Yes the number on the silver dongle matches.

Hello, I received a CS1000 from an online provider for our lab. I was not sent licenses or software - just hardware that was suppose to have been configured. Of course, I cannot get the switch to boot to a prompt. To make it worse, the company will not support the switch and refuse to provide...

This has been fixed. It was a wiring issue between the 66 block and the jack. Most likely loose punchdowns. Thank you for your help and Happy New Year.

The TN is Card 2 Unit 0. So I used ENLU 2 0. I'm a little nervous to do anything physical to the switch. This is a small emergency dispatch center with two seats - now one. Im screwed if I lose the last seat. I think the card has 16 ports.

I did LDIS 0, found the port listed, and then ran ENLU "Card" "Unit". Reran LDIS 0 and the Unit was not listed. The problem I have is that the phone location is in Eastern Europe and I'm working with the local tech who has less experience than me - which isnt much. And since this is a secure...

Thank you. I have tried ENLU and reenabled the TN; however, this did not change anything. I believe it was locked out since the switch didnt see the phone for more than 24 hours. If I plug in the phone, will I at least see lights flash no matter whats going on with the switch?

Happy Holidays to all, I use a Nortel Meridian Option 11C Mini with M3904 phone sets. I have one phone that will not power up - no lights, nothing. I swapped phones and cabling, made sure the power was good, but the issue remains at this seat whereas the equipment from this seat works at a...

Thanks Firebird. I think its easier to find someone who can read ancient hieroglyphics than to find someone local to troubleshoot this switch. Believe me, I tried. I did put everything back but I'm still getting OVL428.

Hello scholars and gentlemen, I discovered that the PCMCIA slots (tracks?) on my SSC Nortel Meridian card were broken which prevented me from backing up. CALL SERVER/MAIN CAB VERSION 2121 RELEASE 4 ISSUE 50 W IDLE_SET_DISPLAY NORTEL So to increase the stupidity of the situation, I had another...

Thank you. I was able to set a loop for 03 24. My issue was that the DDB was not setup correctly. This allowed me to set the DLOP and for the system to recognize the card in slot 3. I went through the remaining steps of creating a D channel, route and trunk. Everything seems to be enabled...

Below is my CEQU print out

No, the PRI is available; if it doesnt appear that way its because I messed around with it. Is H.323 an option across a tie trunk? I'm pretty sure the CEQU is not set right for the PRI. I cannot bring up the TMDI card - it doesnt even list it with a STAT command in LD 96. Would you happen to...