Search results for query: *

There is a Long Distance Verification number you can dial to Identify your Long Distance carrier. I know it is a 700 number, however I cannot remember it fully. It could be 700 555-4141 or 700 555-5555? anyone remember?

Trouble isolated to 206E Module in Slot 5. Internal issue inhibiting Mode Codes. Every other board was replaced to no avail. This was the last board removed from backplane

Yes, TTT, it is a Partner Mail VS R5. It has been in service many years w/o issus. I am going to change out the Proccessor today as changing out the VS R5, had no effect. Are the Mode Codes generated by the Processor or from other boards like links in a Merlin Legend?

nothing rogue. I setup busy lights for the 4-extensions and they hunt thru. I can call each extension and they answer the same as the collective 777 hunt grp button which will either be, "Your call is being transferred to the receptionist" or "Welcome to Partner mail" Incoming calls from the...

The Voice mail access Btn (777) connects to "Your Call is being transferred to the Recept" Any Thoughts?

When you go off-hook while directly plugged into a suspect port, if you get no dial tone,jump over to your intercom and see if you get intercom tone. If you do, then test your C O lines for dial tone. Your Telephone is programmed for "Auto-Line Select" and the line it is accessing could be dead...

You need to go to "Operator Positions" in SPM (System Programming) and delete them from there.

Bad Register? (Link, in a Merlin) 200 Cards Notorious

This is a common problem in the Legend System when there are not enough Links (or a bad one) In the Partner System, the links are referred to as "Registers" and they have the same responsibility (Handling analog duties-"Mode codes") certain Circuit packs, have "registers". If you dont have a...

Unplug cable plugged into port. From System Program, perform a "System Reset-Save All" #728. After reset, plug tel directly into port and see if it restores.

The 012-card also supplies 2-TTR's (Touch Tone recievers) used w/Voicemail & to turn "Message waiting" lights on & off.

When an Ext. is call-forwarded, it will give a single-ring reminder.Try entering the cancel-call-forwarding code.

Why didn't the 2nd 412-card go into the last slot? Did you move all the other cards over to accomodate?

OK, thanks TTT! I was hoping to ultilize NOS "Baby" 206 standalones. I will upgrade to ACS. This will work. Thx again!

Fast-paced Garage needing MOH. Will have 1-12-btn display & the rest panasonic cordless. For the cordless to place calls on-hold to initiate the MOH, what would be the proc . . .

Start w/ a system reboot (#728 in system admin) Often this will clear any transiate errors. If you are able to peer into the port,you may find a pin issue. Expansion, will add 8-more ext. ports.

Apparently, you don't have a Backup/Restore card in the slot next to your VM card. Get one and Backup your programming. I give them away just to avoid situations like this.

*02 - is a "touchtone reciever" test. Must be tested w/ an analog (single line ) telephone. Off-Hook - *02-01, *02 -02 ETC. You will get station dial tone after entering your TTR #, then you go to your TT-Pad and enter all the digits, 1-2-3-4-5-6-7-8-9-*-0-#, then confirmation dial tone. If TTR...

You may have DT "swinging-open" at the RJ11-Mod.plug. Best way to test is to dial *03-2723874-05 from intercom. Then you can check for the open (while hearing for DT).

Thankyou TT! They have Merlin Messaging. The Client, recently reconnected an ext. that was disconnected for a time. In doing so, a new 800 number (Private Line), was added to the extension. It was later discovered that the ext. was in the "Customer Service" call group which it was removed from...