Search results for query: *

I will take a look at this scenario, Thanks.. www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

I don't have CFC in the inbound route. I tried it in the inbound route but I was not able to turn on or off. What I want is for the receptionist to have the capability of routing calls to Vmail when she leaves her desk and to be able to place in in night service similar to the Call Pilot or...

Once call flow control has been activated shouldn't the calls be routed to the IVR...Incoming calls are routed to ext.and I would like to have the calls routed to Vmail with the activation of F*280..Vmail works fine when incoming calls are routed to call flow control but would like to have the...

Thanks to all of you. We have resolved the issues by disabling the firewall in UCX and rebooting system. Everything works the way it should now.. www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

Hey ucxguy, Thanks!! I did perform the auto config it populated all the parameters. I noticed that the gateway address was different so I put in the correct one and I am able to make calls and both parties can hear. However, I am still unable to receive calls.. I had this same problem some years...

I have two sip trunks on ucx50 w. 4.0 software. Unable to receive incoming calls and on outgoing calls ok except called party can hear caller.. Trunks have been up and running on this system for several years...Provider is voip.ms/performed echo test (ok) and swapped pop servers with no luck...

Hey UCXguy, I did check the logs and it is sending the caller id with or without brackets. However, it is not over-riding the trunk callerid even if the field is left blank. Must be a block by the carrier.IDK Thanks Set("SIP/210-00000065", "USEROUTCID=<9xxxxxxxx>") in new stack [2015-04-28...

I'll take a look at it later on and let you know. Thanks www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

It doesn't work even if the route is flagged as an emergency route. The same caller id is sent no matter what. So this tells me that the CNAM from the carrier has priority and so far this can not be changed.... www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

That means for every extension that I want to send out a different CID for,I would have to do this. So basically the UCX50 extension CID does not override the trunk CID as it states for outbound trunks.... Should not need to implement methods for the system to do what it's purported to do...

I have one office and I want the extension that is making the outbound call to send a CID different from the Trunk CID it is using. It is one sip trunk with 25 channels. www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

That is exactly what I did and I get the same results. Would CNAM from the carrier on this sip trunk prohibit me from overriding the CID sent? www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

I've tried that already and the CID for the set is not sent. Is there a particular format that has to be used when typing in the number for the extension CID? www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

Has anyone been able to program an extension to send CID that would override the out going trunk CID on the UCX50? www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

I changed the context to "from-internal" and it cleared my problem. It appears that some of the old custom context dial plans that I created were still active after deleting them. Dial 9 restriction is still active even though I have the extension programmed to allow all calls with no...

I am unable to make any internal calls on extension 210. I haven't any restrictions on this extension either. Whenever attempting to dial internally I get a busy. Report reads as follows when dialing voicemail *97. [2015-03-10 19:16:49] NOTICE[28546][C-00000054] chan_sip.c: Call from '210'...

On the web interface for the extension, you can scroll down to call restrictions and set to restrict long distance dialing... www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

Figured it out. www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

I have configured my AA and I would like my operator to have the ability to send calls to the IVR when she is not at her desk. How should the call flow toggle control be configured for this to happen. www.voiceconnectplus.com Voice Connect Plus, Inc. have a great day and a better tomorrow

Hey Ucxguy, thanks for all the input. After stripping everything down and reassigning to different server, I was able to get the trunk re-registered with other server on the ucx. My issues for the most part appear to have cleared up. Still getting break up now and then though...