Search results for query: *

Here's a PMSI example: PMSI MANU PMS1 PMCR 20 PORT 1 XTMR 0 PTMR 0 NDIS 20 OCAC NO MTRO MR SBA_ADM_INS 000 SBA_USER 512 Is it set to Port 1 or still port 5?

The command to enable D-Channel is ENL DCH 5 Not DCHI Normally you don't need to enable D-Channel, when you enable the loop in LD 60 it also enables the D-Channel Are you sure you've got the correct PRI Card, NTAK79 is DASS/DPNSS & Nortel Propriety QSIG (Networking between Meridians) The NTBK50...

Mike Call Pilot has its own license which is not tied to the Meridian PBX Site ID You can see if it boots up by connecting a keyboard, mouse and screen to the front at the top. Administration is done via call pilot manager (which you should be able to down load from the web) on the CLAN It...

Also if you look at the LD 60 STAT, Channel 24 for each Loop shows the assigned DCH. PRI* TRK LOOP 200 - ENBL FFMT/LCMT/YALMT: ESF/B8Z/FDL TRACKING SERVICE RESTORE: YES YEL ALM PROCESS: YES ALARM STATUS : NO ALARM CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD * CH 03 - IDLE TIE VOD * CH 04 - IDLE...

Status LD 96 STAT DCH LD 60 STAT

LD 96 DIS DCH <DCH NUMBER> LD 60 DISL <LOOP NUMBER> ENLL <LOOP NUMBER>

Is it the ACOD of the incoming route?

The trace you posted: ORIG 002 01 TIE RMBR 15 1 Call incomming on route 15 member 1 (TN 2-1) TERM 007 0 00 12 MARP 0 7992 L500 Call being presented to extension 7992 (TN 7-12) This implies the call is routing successfully to the remote site, hence my question, does it work locally Can...

Can someone on site at the remote site dial 7991 / 7992? as these appear to be analogue ports at the remote site, Have you checked the analogue card 7 at the remote site, STAT in LD 32, also try an DISC 7 & ENLC 7

I have always got round this by setting a static route on the default gateway which points traffic bound for SIP Providers IP to the SIP Router.

You could try the return to queue option in LD 23 ACD config: RTQT (Seconds) Time ringing on handset before call returned to the queue. RTQO (NRD / MSB) State the agent is changed to after a call is returned to the queue.

Look at Networking Data - Network Numbering Plan, If you look at the Overview, you'll see how the 31xx site is configured. To add additional sites use next available index and add require network information.

If you create a MCR key on a phone, the user will be able to dial out using it, regardless of whether it is associated with a virtual/phantom phone or not.

As I posted the other day I suspect its the PE Power Supply located next to the Ring Generator

If you do an XVR you can send the XBK file back to the system and it will check the downloaded XBK matches. >LD 143 CCBR000 .XVR

Possibly a Faulty Power Supply Unit, one of he various voltages supplied by the PSU is for ring gen.

I had same issue on an Option 11C about a month ago, the software daughterboard was corrupted, replacing DB, re-installing software and a backup resolved issue. Don't reboot system as the one I worked on did not come back up, when I subsequently tested the corrupted DB in the lab.

Sounds like its a Small MIRAN, ie only Licensed for 2 Channels

What normally happens with multiple consoles is if a console goes into night mode it shows busy as long as at least one other console is still active, when the last console goes into night mode then they all show night. Alternatively if you press shift + night it forces all consoles into night mode.

Could be a faulty SSC card, I've had to replace a few with the same problem. Its normally straight forward, power down system, remove SSC card, swap Security Device and Software Daughter Board to replacement SSC Card, replace card in system and power up.