Search results for query: *

I have had some luck with diskformat. Log in using control ldb Username pdt2 and password for pdt2. ldb> diskformat This will erase all and restore the gold image.

You are having loss of framing errors on your PRI. Has anyone checked the clocking? Is it clocking to the primary clock source or in free run. If it is free run you will eventually get slipping. The PRI must be clocking to the primary or secondary (if you have one)source.

The VAS008 and VSID 9 refer to the voicemail AML link to the PBX. Do you have Meridian Mail? If so it looks like the link is down. If no mail the AML and Vas can be removed so these messages won't appear anymore.

Virtual office login refers to IP sets. The set must have VOLA in the CLS in order to login your set configuration at an IP set in a different location. Each set must have VOLA in the CLS of the set. Its hard to tell with the limited amount of info you have posted.

Looks like you are having a problem on your loop 2 with Pri trunks or digital ties???

When the SCPU command was issues the problem followed the Core. After splitting and doing a sysload on each core the problem is resolved. Thanks to all.

The file exists on the RMD as well as on the core. At this point we are going to do as KCFLHRC is suggesting but we are going to SCPU's first before splitting since things may be okay on the inactive core so after splitting we can work on the core that is having the problem. I just thought there...

Haven't tried it since the customer won't let us switch cores at this time. Midnite routine to switch cores is disabled. I would also like to mention this is Rls 5.00w.

I have a CS1000E CPIV redundant Core 0 and Core 1. When doing backups it will not backup to the RMD flash card. Message shows: SRPT4619 WARNING: Last Archive Procedure had failed % No archives were completed since Apr 23 03:16:00 2013 % % % TEMU020 Errno 0x38001c: Failure opening file...

When ordering 1120E sets thjey have 3 different codes. One is with key caps with icons , one is with keycaps with english(ROHS) and one is an 1120E GSA. Does anyone know what the GSA stands for? I think it refers to having an external power supply but I am not sure.

Is it possible you need a value at the FLEN prompt for the number of digits being dialed?

Thanks for all the input. We have finally resolved. Avaya has graciously produced the patch we needed.

Thanks Janaya. This patch would fix our problem but it was not written for Rls. 5.00W CPPIV only for Rls 5.00W CPPM. There was one for release 6. We have contacted Avaya and they said they are no longer writing patches for Rls 5.00 so we are out of luck.

I have just been informed the WATV version is for Military and Government sites.

Thanks for the info Firebird Scrambler! At this point I would have to assume the WATV is the DSN version.

Yes, One would assume that but does anyone know the what the difference between 5.00W and 5.00WATV?

I have a CS1K Rls 5.00W. I need a patch (vendor only available) but the paticular patch is written for Rls 5.00WATV. I am not sure of the difference between Rls 5.00W and 5.00WATV. I think it has to do with a National defense version I'm not sure. Does anyone out there know for sure and could a...

I had a similiar problem on a CS1K Rls 5.0 going to a BCM via H323 trunking. In the node properties under the G711 codec I had to adjust the Voice payload size (defaults to 20 or 30?)to match the same voice payload size at the far end. This fixed my one way speechpath problem.

Thanks for the input guys. It looks as though its a re-install from scratch. You'd think changing an IP address wouldn't be that difficult. Not to fond of this system!

I originally changed them thru base manager under the network id. When I redeployed I can't access UCM so I went thru the baseparamsconfig and it showed my changes had been done.I changed the EM IP in EM but that is where I got stuck with the SS since it would not allow me to change it nor would...