Search results for query: *

Hi Jonah29 Please check all timers that relate to 20mins to 30mins? If there isn't a timer that reflects this time then it's more than likely the other end at fault. I had it once before where an engineer had mistakenly turned on pre-pad call and the calls dropped when this timer was...

iPECS SIP call cuts off after 30s If iPECS SIP call cuts off after around 30s, check SIP ALG is disabled.  On the MicroTIK router the SIP ALG is called SIP Helper and should be disabled. Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

Go to any handset Press TRANS/PGM Press 78 Press *147* Scroll through the settings using the volume up/down key Note down what the IP address is under MFIM IP Address. Go to the new handsets, repeat the above and enter the IP Address above using the keypad. Use the star button for a dot...

RR PGM 151 in CO Line Attributes, COLP and CLIP Index set both to 'Use Station CLI', add the zero in for 'My area prefix code'. Should be ok with that. All depends on the SIP provider really, we use Gamma which is IP Address authentication. Eats Ok, Press Trans *#..... TRANS/PGM..... the...

RR We have to make sure 'CLI Flexibility' is active on our SIP providers portal. Then we use the CLI STA in pgm 113. Line 12 - STA CLI 1 Enter full number you wish to display. Cheers Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

What happens to the 70% of calls? What do you receive from the network? error, busy or silence? SIP ALG off on the router Keep Alive needs turning on maybe Does it happen if no one is on the phone? ie, no one on a line and a call can call in ok? 2nd call doesn't get through or is it just...

Do you have enough IPCL licenses for the SIP Trunks? Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

Hi Does anyone have the depth of the DTIM24 and STLM32 with the lead attached on the back? I have a shelf within a cupboard that the current IPLDK100 installed and will be replaced with a UCP and above units. I only have a certain amount of space available. Thanks Eats Ok, Press Trans...

Hi Can you program a flexible key as the 'Directory' button? The LDP9224 handsets have a designated 'Directory' button. I would like the LDP9208 handsets to have the same key if possible using a spare flex key. Cheers Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

Hi You will probably find you haven't opened up the audio channels. 5588 5060 6254 7000-7335 6000-6048 8000-8048 9000-9048 10000-10239 All UDP ports. Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

The VMIB is only a 4 channel auto attendant card so really it would be the 5th call that would follow ring assignment. Unless your using an IPLDK20 which is only a 3 channel card. Is anyone listening to voicemail at the same time or using the vmib to control the music on hold? Eats Ok, Press...

Bazza I know you've change the cabling but have you tried popping the extension direct on the TJF? This would complete eliminate all wiring. Could be a dodgy connection on the Krone strip for that pair, you could take the wire off and move it to a spare part of the krone strip. Eats Ok...

Aarmax 'Open Loop Detect Timer' is the one you need. Contact you provider and ask them to change the 'Open Loop Disconnect Timer' to 800 Milliseconds. This is the time for BT in the UK. May be a different timer in other countries. This is taking into account the lines you are using are...

Hi This is the 'Disconnect Clear Time' located in CO programming around PGM142/143. In the UK we need this to be set to 05 (500milliseconds). You will also need to ask your line provider to set the lines on the network to 800milliseconds, this will prove to be the hardest part of the job...

Hi If you connect line port 1 to SLT port 1 you can use another handset and press line 1 and the SLT will ring. I think! Cheers Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

Hi You can test the LCOB card by piggy backing a port from the SLIB card but to test the STIB and BRIB cards you will need an active ISDN2 circuit or an ISDN2 emulation tester. You can check the card registers etc but you will not if the ports are working or not without this tester. Eats Ok...

Jonah29 :-) Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

Hi You could try programming a call log key. Trans/Pgm Spare flexible key Trans/Pgm 57 Hold/Save Speaker Pressing the button now will give you options to press 1 for Received Calls 2 for Dialled Calls 3 for Missed Calls Cheers Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer...

Hi The manual does say the following: For SLT analogue device Call CO party 1 answer Press recall Dial CO party 2, answer Press recall twice within 2s to set up conference Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

Hi Mark If you get another model of handset, LDP7008,7016,7024 and plug it into the socket then plug the original 7004 back in the socket the flex buttons will default back to normal. Eats Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!