Search results for query: *

Thanks, we have tested this a nd still no joy, we will be replacing the Prolgox card this evening

Thansks , we have and confirmed that there is dial tone

We have recently replaced an Audix LX 1.1 with Audix LX 2.0. Yesterday channels 2 and 4 where answering and now today only 1 and 3. You can see the non answering channel been active in Channel monitor but it does not answer. Please could you possibly advise where we can look

Hi Does anyone have recommended switch configurations for NICE Perform NiceLog VoIP and 3Com® Switch 5500-EI 28-Port thanks T

Hey dwalin... did you ever get info or test your labs connecting a Cisco ATA device to an Avaya., I saw in some posts that you had tried or where trying? I found some info in http://www.tek-tips.com/viewthread.cfm?qid=1208811. But looking for substantial answers Thanks Terence

Hi have found info @ http://www.tek-tips.com/viewthread.cfm?qid=1208811 Thanks Terence

Hi Has anyone managed to setup a SIP trunk to Exchange 2007 Unified Messaging with AVAYA CM3.1.2 (h.323) I have the following: Avaya s8300 CM 3.1.2 on a G700 Aavay SES 3.1.2 on a s8500 in simplex home/edge. Any help would be greatly appriciated, Thanks Terence

Hi Mark. Did you have any luck? I need to do the same thing. Thansk Terence

Hi Has anyone been able to use a Cisco ATA 188 with AVAYA CM 3.1.2. Thanks Terence

Cool well done! Hope I helped!

yes I did, what version of CM are you running? work@palmerfamily.co.za

yes the LSP in inservice/idle. On the LSP it states in the logs: illegal connection attempt from 10.11.1.132 Host 10.11.1.132 is not a valid source. connection from 10.11.1.132 port 33678] I have doubled checked my LSP information in configure server aand it is all good.

hi I have an s8500B(CM 3.0.1)with a s8300 LSP(CM 3.0.1) in a G350. When I try save translatiosn to the LSP I get the following erros. Please Help: s8500B: 20061101:000555843:432:filesyncd(6879):MED:[Performing filesync: set = pwd, type = LSP, targets = 2, bytes = 678]...

Hi Guys thanks for the information, RFWatts, How do I check/enable that "Faststart" is enabled on AVAYA. whatsanavaya, Can you send me your network region 4? thansk AvayaEng

Hi I have a s8300 in a G700 running Avaya CM 3.0.1 and need to setup up H.323 Trunk to an Asterisk 2.3 PABX using openH323 1.1.2 running on CentosLinux. The link runs between a PIX firewall. With the ip address of the Asterisk and the s8300 able to see each other. The IP of the MGP VOIP engine...

Hi I have a s8300 in a G700 running Avaya CM 3.0.1 and need to setup up H.323 Trunk to an Asterisk 2.3 PABX using openH323 1.1.2 running on CentosLinux. The link runs between a PIX firewall. With the ip address of the Asterisk and the s8300 able to see each other. The IP of the MGP VOIP engine...

thanks for the help will investigate further

Hi dwalin. In intra-system ip dtmf transmission mode I have in-band or RTP-Payload only. thanks

thanks, Okay what I have done is routed all my calls that where going to the PSTN via the G700 to an S8500 and braking out there. there is no QOd issues. I'm not sure where to find the synchronization on a s8300 with G700.I have set up a second DS1 card in the G700 and made a call using a Trend...

Hi Have an IP phone 4601 on an G250 registered to an G700+S8300. When I call another IP phone in a different location the QOS is fine. When I brake out to the PSTN via the G700. I get very bad GOS. all my IP-Codec-sets arre G729A. the VoIP on the G700 is using G729...