Search results for query: *

I have CS1000E 7.5 and Session Manager 6.2 connected to a Cisco UCM Release 7.1 I think. Setup: PSTN call inbound and terminates on 2616 or 1140. The Cs1000e set user then blind transfers call to Cisco via CDP/ Session manager over SIP. The Cisco set gets the CLID of the 2616/1140 and not...

Yes I know its old but the customer still uses it for several thousand sets. I’m not overstating and Im not about to fix the entry’s manually through employee selector.. When I run an extension report using the web TBS the name is wrong. Now hold on here is what I’ve done. They do not use...

SIP 3rd Party has been in and working for a year CS1000e Rls 6 with SIP Line Gateway. Just found out no Intl dialing. Local, LD and in are all ok. These are third party sip-3 sets. The call is going out as national and not international as carrier wants it for call type. It is correct for...

Got it. Thanks.

I’m adding another MGC CS100E R6 cabinet for a NT5D14 Lineside T1. There is not a PRI with clock in this cabinet (AND I DON'T HAVE ONE). The NTP is vague regarding this subject ds, maybe someone with actual experience can help. I’ve been "told" that a clock isn’t required if you are not using...

Don't get it. The book shows mutiple ERL and states to use RLI. Can you be more specific like fix my print and repost. Im not a programmer and ours is out until the first of the year.

This is a CS1000E on RLS7.5. The trace shows that 9911 is being sent to telco when dialing 911 or 9911. I have looked at several ESA examples but, not quite getting it. Here are the prints. Can someone tell me what is wrong? >ld 90 SPN 911 FLEN 0 INPL NO CLTP NONE RLI 120 SDRR NONE...

Even though the sets are on 3904da94 there is a known issue with the AOM. Force download the set again and see if this resolves it.

There is a signaling issue. I have Avaya case now to find out why call is disconnecting. I also have one-way and no speech path at times.

Yes all programmed and enabled.

I have a CS1000E Rls 5.0. All SigSvr, CallSVR, MGC are PEP and loadware current after issue started so, that didnt fix it. Anytime a transfer occurs from Callpilot,MICA or TDM set to any H.323 trunk (12)locations it fails. Does not fail everytime, but most of the time. Checked DSPs in three...

Im going to jump in since I fixed two of the similar issues within the last two weeks. Change the NTRC49 clock cable like Jeff suggested. We have had several "just go bad". Might have to change the dip switch on the NTRB53 clock card to 15-20 ft since this is total length. Check the other...

I know it sounds simple but, the CS wont let go of the SS ip. I even removed node and ss. Some where in the node.cfg file it still thinks it is co-res even with the SA software. New SS with New IP wont even register. Im starting over after lunch. Thanks

So I can't seem to find any docs of how to complete a Co-Res to SA. The Avaya docs say You can upgrade a CPPM Co-res CS and SS- based system to a CS 1000E (VxWorksbased)SA with a stand-alone Signaling Server if the 1000 IP and 800 TDM users limit is exceeded. For details see Avaya Communication...

I have a I2033 that boots right to this message and all three leds are lit. i think this happened since it "might" have been S10 and someone tried to go directly to S74. LOADING: Loading boot parameters... Installing bootrom and recycles. I can't get into setup to load firmware, since no...

MPLR27705

Have you installed a recent DEP list on the sig svr. If so there were a few bad PEPs the last 2 weeks. I ran ito this problem yesterday.

I have has this happen on three recent CS1000e 5.50j installs. The admin1 password disappears, in other words nothing works. After an upgrade the password change doesnt take, you can't delete it. I have fixed it with an ini. I havent tried PDT and didnt find a PEP. Any ideas? If you know...

Issue resolved

On several of our CallPilots the server name shows up along with the other choices in the "Preset Server List" dropdown box (last server and manually). This isn't a CP web svr. I enter the name by clicking the enter server name manually, then login. After logout the only choice is: enter...