Hello, what's up with this? worked for a while now flashing green. Here is the scoop.
ip 406v2 DS 5.0(20)
analouge pots2 5.0.20
dig dcp 8 5.0.20
dig dcp x 30 57.0.20
analouge pots8 6.2.23
all was working fine.
Suggestions?????????
tried rebooting, check connections..
thanks
ron k
Hello all. I have a company that has a main office with 5 satalite locations. We have installed an IP Office at the main location and so far have upgraded two sat locations as of now. I would like to network them all together so they can share the same dial plan within the company.this may be...
Hello all. I have a customer that wishes to have add a second 6 port exp module.
They are at MICS 7.1 now. I understand i have to convert them to 7.1 XC.
I have been told conflicting procedures on how to perform upgrade. Would / could someone explain proper steps.
Thank you.
Ron k
Hello, i have a customer that has a 877 telephone number and they want to route inbound calls to certain area's depending on the area they originate in.
Who offers this service??
thanks
ron k.
Hello all, I have an IP Office 406v2 st up and running fine. I need to put a phone at a satalite location. I have a linksys rvs-4000 at each side with a vpn tunnel and shows the tunnel is up. I am not sure the IP Phone can see the system. here are the settings.
main office
IP-OFFICE...
Is it possible to steal a call after vm picks up??
Calls come into group 300 after 4 rings goes to vm.. I would like to be able to intercept call, if poss??
thanks
ron k
Hello, I have a customer that has an ip-office 406 at the main locations ans is going in with a ip-500 at one of the subsites. I need to link the two together. Both for 4 digit dialing back and forth and centralized vm. The subsite will have an ip on the same network as the main site. 4 vcm...
Hello all, I have a 406 with v 4.0 and my analog port 202 has a modem attached. I need to have the modem call x-xxx-xxx-xxxx then wait for an AA then continue on with xxx.
Any thoughts??
Thanks
Ron K.
mattKnight:
I can not seem to downgrade......
open mgr.
change \workng dir
set to C:\Program Files\Avaya\IP Office\Manager\V3_2_999
(two files are here:ip401ng.bin and nadcpv2.bin)
choose File/advance/upgrade
wizard starts
shows only ip 406 (not selectable.)
duh
What am i doing wrong...
ProviderReborn :
The ds 30 firmware is at 6.1(9) the software is 4.1(9). I did just upgrade anyways , however it shows it at 4.1(9) with 4.1(9) avail.
I call station 213 (4406) ring , ring, ring i hang up. System status then shows:
call ref call timer originator,calledprty current...
Hello all, i have an ip 406v2, 4.1(9) equipped with 2- 4 line cards, ds30 v1 rel. 6.0(7). It seems like after the upgrade to 4.1 I have had digital stations 215,214,213 all 4406 telesets, randomly go off hook ad display both the red & green light. If i look in system status, it,they show up as...
Me again, by going to http://marketingtools.avaya.com/knowledgebase/ipoffice41en/html/smdr/index.htm
and browsing to my "smdrlog(backup2-24-2008).csv" file, this should read the file and display the contents correct?
What happens if explorer/firefox just sits there and has the blank screen...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.