What VERSION is the Magix ?
I "think" (scary) anything before v3 does not have the Delay, or cant do the cascade notification thing ..
A few things that need to be ...
----------------------------------
Restriction (under extensions) set to 3
ARS Restrict (under extensions) set to 3...
HiDesert ...
You can find a PRI cheat-sheet in the FAQ of this forum..
I'm with everyone else here ... DONT use QCC type operators ..
If you choose to keep the other 2 as operator positions, give them a PICKUP EXT xxx of the first operator as well, and have them ANSWER the call from the...
Hey... I know that one ... !! Most are familiar with that as the code to enter programming locally on a phone
but yep .., add it to the List!
MrTelecom1
Re-Living the AT&T/Lucent/Avaya issues since 1979!
No, you DONT have to use the built in CSU.
Ooo no .. one of those circuits delivered and connected to a ROUTER..? PBX connects to router..
When they first started doing this, the EMULATION of a CO circuit by a router was pathetic.
MrTelecom1
Re-Living the AT&T/Lucent/Avaya issues since 1979!
Most Long-time & long-Ago phone techs are not gonna know BOARD LEVEL failures ...
We find the port doesnt work, we dont use it.. Mark it BAD! When failures occurred back when ATT supported
them and I was a business partner, we simply replaced the control unit.
None of the dealer Dealer & ATT...
They were back in the day, to AT&T, THE SYSTEM..! You'll see a few here and there, but many went away with the onset of localized voicemail .. These didn't have the ability to support local vmail systems typically. Yeah, one was made for them, but I saw 1 of them for every hundred classic...
Couple More for ya .....
Intercom *08 tests the Flex board of an MLX set.
If all lights are Green it's good.
Test Internal Dialtone *01
Verify a Systems Release and Version *05
Test message waiting Lamp *09 (hear tone) hang up. (lamp should go on)
MrTelecom1
Re-Living the...
Yep, MUCH preferred to use a digital trunk to the switch, especially if I can get a PRI to it. A channel bank vs a PRI is like Dial-up compared to cable/DSL.
One thing I found in numerous cases, after they started using ROUTERS to emulate a CO Circuit.., almost every Legend that made that...
R4 Magix has the Ring All group for sure .. I dont recall without lookin it up if R3 had it or not... either way if yours is earlier than 3, it doesnt have it, and you'll have to use a workaround similar to telecomboy said..
You can verify your systems version by grabbing an internal dialtone...
The Legend system was/is a Rock, just like it's big Bro DEFINITY.
I have legends that I installed in 1995 still running .. I try to get em to update but they dont wanna change whats not broke and does the job...
Legends are as easy to program as the Merlin Plus.. and lots more
functionality if...
OMG a Merlin Plus! haven't seen one of those for a decade!
Just a thought, since they are dirt cheap now..
Get a Legend processor for it and you'll gain many additional features and be able to use portions of the Windows GUI SPM for programming.
Use at least a release 3 Legend(6.1 would be...
I had that one occur to me a couple times. An obvious port that SHOULD be able to be assigned and couldn't. I tried assignment on a different card and it was able to be assigned as Page port ...
Turned out I had to Flash the Firmware of the 408 since it was in a magix.
Try assigning it on a...
The transfer return time/rings needs to be higher than the Group Cover rings, or it's not going to goto cover.
Often I set coverage for the operator extension to route to the AutoAttendant during day, and General MB if office is not occupied at night,
and use an adjunct ext with primary cover...
Just got remote access to both systems setup.
Got pulled into this from a Nortel Guy
Found the 6.1 Network Reference on the switchroom floor!
I had to secretly laugh my ass off!
2 Ea. Magix 4.0 systems.
SYSTEM A
Voice PRI and a 100D for a Point to Point.
Point to point is UP as a PRI...
The coverage settings are per extension, in the extension settings ..
The GROUP Cover is typically your setting before it covers to the vmail calling group.
The Primary Cover setting, is how many rings before it starts ringing the Primary cover stations.
Review secondary cover as well ..
Do a...
An Operator position with a mailbox .. hmm That's Not usually done.
Maybe I'm mis-interpreting or don't have all the details ...
Operator can be in the COVER GROUP and maybe send it to an Attendant, but seems
unique that your saying calls not returning to (The Operator's?) mailbox....
Is the...
This begs to determine what your attempting to "7-digit" dial ..
Is this for a networking purpose, or are you in an area like telecomboy mentions (Where they have "overlays" in the city and more than one area code in the same area) and you want your users to just be able to dial 7 digits for a...
Initial PRI Configuration
========================
1. Set DS1 Frame Format to Extended Super Frame.
Lines Trunks>>LS/GS/DS1>>Enter Slot + Enter>>Frame Format>>Extended Super Frame>>Enter.
2. Set DS1 Suppression:
Lines/Trunks>>LS/GS/DS1>>Enter Slot + Enter>>Suppression>>B8ZS>>Enter...
It's basically going to BUMP ALL your extensions downward onto the slot 15, Like Merlinman said,
if you put it in slot 15.
If your Handy with the system and understand renumbering you can do it ..
of course there is always....
And/Or in a "we gotta do it" scenario, do a PRINT ALL report...
I've not tried 7 digit on Magix.
I know Legend could only do 4-digit.
Check the Legend 6.1 Network reference manual "Call Handling Scenario's"
(There's isn't a Network Reference for Magix that I remember .. If I'm wrong,
Please advise!! I'd love to get my hands on it too!)
It provides a...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.