Search results for query: *

This does work - thank you!

Thanks Kozusnik - There's not much more to that where statement, but the $delete_vehicle var is being put into an array (checkbox array) then looped through a while statement for (if) multiple deletes are selected. I suppose that would work, but I was thinking there was a more efficient way to...

Hi all, can someone help me with my query please? I have done some searching and can't seem to find an answer to my query problem. I need a query that will delete one vehicle(v_id) AND all service(s_id) records associated with the vehicle. The problem is that my existing query only works when...

I have the same problems here - working fine but won't email me when the job is complete. Anything else?

If it's a POP3 account, you can add the account to all three users using Outlook. But, beware because that means you have 3 different people sending and receiving email all at different times, unless you setup your send/receive groups a special way. For example, you can have just one person...

Have you tried mapping a drive?

I have a user that cannot see any forwarded .msg attachments (someone sends an outlook message as an attachment) they show as attached but are invisible to the user. Also, right click does nothing in the message pane. The only way I can get either of these to run is to use outlook's safe mode...

Thanks! - That fixed my problem. I wish the error was just a little more descriptive.

I am getting the same - anybody figure out the problem?

Bump for anyone who could help...plz...

Thats where it gets tougher - because you have to use the command line to do ACL's (access control lists) and NAT's if you have any. But the IOS gui that comes with the 800 series routers has a basic setup wizard that will guide you through most of the process. You would then use your...

I have an 805 which is the same as the SOHO - I go to the http setup for IOS and go to troubleshooing -> show commands -> running-config. That will give you a window that you can copy/paste your config into notepad etc. Use ctrl-C/V to copy and paste cause you cannot right click to do so. That...

Assuming it is a web service (port 80) then do this: ip nat inside source static tcp 192.168.0.5 80 171.68.1.1 80 extendable at the end of the last octet just specify 80 for web - for RPD or remote desktop it would be 3389 etc...

You would have to do a running-config to show you current configuration first. How do you interface with your router?

I want to see how secure my router is, just to know if it could be compromised or if there is anything I could do to make security tighter. What could I change? Here is my running config: Building configuration... Current configuration : 6753 bytes ! version 12.2 no service pad service...

Thanks for your help guys I am now up and running, except for mikwire which is not resoving its DNS...but thanks again!! Mike

I called my ISP and made them double check the routing and they found a /28 routed wrong or something. But could someone check out www.mikewire.com or www.wellingtonsupport.com and tell me what you find?

Of course it is...duh I had my IP log in the other room. Thx Here is show ip route: Gateway of last resort is 216.187.177.65 to network 0.0.0.0 C 192.168.200.0/24 is directly connected, Ethernet0 216.187.177.0/24 is variably subnetted, 2 subnets, 2 masks C 216.187.177.224/27 is...

I spoke to them yesterday and they told me that it should be ready to go because it is dual numbered. I am assuming that they have taken care of the routing, but i am not too sure. And out of curiosity why would I want to have my isp route the /27 to 216.187.177.74? Because that is a static...

Do you need to add a static route for NAT? As in, you have an external IP you need to match up and translate into an internal IP? Example: Internet----->external IP -->Router-->Internal IP For that you would use ip nat inside source static command - you can find more info here...