Search results for query: *

Brat, I already did Load Balance with SplitLoad executing Setd -IP control=(Route, SplitLoad), but my router CPU Utilization is reaching 98% (Bad !). Is there any way to track high cpu utilization processes an try to put cpu utilization a little down ? How can we upgrade cpu capacity at...

Hi, Brat ! How can I setup my router with splitload routing ? Just exec command below ? setd -ip control=splitload I have 2 uplinks (Link C - port !6 and Link D - port !7) at a Superstack II Netbuilder SI 532 router, and want to split all load from ethernet (port !1) to 2 uplink...

Hi, I got it ! After firmware update and adjustment on configurations, VPN Frame Relay is interoperating with VPN IPSec (Linksys). I had to put a route at Central Office Linksys router as below. 192.168.0.0 255.255.224.0 192.168.50.254 192.168.50.254 (Cisco router - Frame Relay...

Folks, I updated firmware in both Linksys BEFSX41 EndPoint and, now, VPN doesnt work. We had firmware 1.45 release and ewre updated to 1.50.9. All configuration are ok. I am begining believe that at Central Office we have to put a BEFVP41. I will test ! regards, Topoh

Matt Wray, responsing your questions ... 1) You say you can ping from a remote Cisco to the Linksys but not beyond ? R- Yes, I can ping from remote office on Frame Relay office to Central Office Linksys. But ping dont reach up to remote Linksys, through IPSec VPN. 2) Who is the...

bcastner, but I can ping from concentrator cisco router to remote Linksys VPN office. Then, ICMP traffic is being encrypted by Linksys and trasmitting to remote Linksys office. I disabled All kind of pass-through and it doesnt work. But I will talk to Cisco. Tk's, Topoh

Hi, I have used a long time a Frame Relay VPN that has many remote subnets and a concentrator subnet like description below. Recently, I install internet cable access at Central Office (Frame Relay Concentrator) and other cable internet access in other remote office to begin migrate all...

Hi, MCSEstudent. You can share your cable modem access (only one valid IP address) using NAT. For example, if you have a valid IP address 200.199.60.1. Connect ethernet interface of your cable modem on LAN ethernet of a NAT server with cross-over cable. Do a point-to-point ip connection between...

Hi, Brat. I think you can do it using NAT. In this case, I´m suposing you have 16 IP valid addresses 200.199.60.0\28 (including broadcast and network addresses) and a private network using non-valid IP address range 10.0.0.0\24. Try doing the following, changing these IP adresses to that match...

Hi, Worker99. Sorry for response, but after repeat proceedings it works. Thank´s. Topoh.

Hi, tjamm. Try to use main menu FR or use the folowing commands. SHow [!<port> | !*] -FR CONFiguration Checar todos os DLCI´s existentes SHow [!<port> | !*] -FR AllDlci To check DLCI´s configuration SHow [!<port> | !*] -FR CONTrol To show diagnostics of FR PVC´s SHow -FR DIAGnostics To...

Hi, Dread. What´s the software version are you using ? Boundary routing mode depends of version you are using, its not a option you´ll find searching menus. It happened with me cause I was using Supersatck II Netbuilder 222 with software version 9.3, BX. This version already set the router to...

Hi, jdpunch !!! There is two possibilities to solve your problem. Or the console baudrate configured is 2400 bps, 4800 bps, etc(except 9600 bps), or console cable pinout is wrong. Have you ever tried another console baudrate ?? Did you check console cable pinout ? Tell us the console cable...

Hi, Brat !!! It was successful !!! Thank´s very much one more time. Where can I search about these kind of troubleshooting ?

Sorry, I forgot to give more information. I´m managing a VPN Frame Relay (WAN) with 4 branch offices (three 3com 3C2XX routers and one Cisco 805 router) and 1 central office (3com router 3C2XX). The company is expanding more 2 branch offices and it adquired two Path Routers (Cyclades) to...

Folks, I´m having problems to link with Frame Relay protocol a 3com router (3c8200) with a Cyclades Path Router. Does anybody knows a case like this ?

Thank´s Brat, one more time !!! It works !

Hi, Worker99 !!! I did the procedure and it works. But when I enter any command appears the message &quot;Error -Subdirectory name is file name&quot;. Is there other additional step to do ? Please, help me !!!

Brat, i´ve tried following the procedure but it doesn´t work ! Do you have any idea what I did wrong ? See below the messages that´s showing: Enter Boot Filename (CR=no change): 10.0.0.1:/boot.68k 1. Client 10.0.0.2 2. Server 10.0.0.1 3. Gateway...

Hi, worker99. Where can I find documentation about User and Diagnostics Command Menu. I erased primary and secondary boot.68k, by accident, of router 3C8222. Your procedure works in my case too. Tk´s a lot !!! Topoh